Results 181 to 190 of about 468,087 (314)

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

open access: yesAdvanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi   +3 more
wiley   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

open access: yesAdvanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera   +8 more
wiley   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

open access: yesAdvanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Consumed by Abdominal Distention

open access: yes
Arthritis Care &Research, EarlyView.
Abimbola Fadairo‐Azinge   +3 more
wiley   +1 more source

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

open access: yesAdvanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham   +7 more
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

open access: yesAdvanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin   +2 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

open access: yesAdvanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira   +4 more
wiley   +1 more source

Ion-shielding ultrathin encapsulation with hot-press bonded interface enables chronic stretchable bioelectronics. [PDF]

open access: yesSci Adv
Jiang Z   +15 more
europepmc   +1 more source

Home - About - Disclaimer - Privacy