Results 191 to 200 of about 6,842,466 (349)
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
Analysis of the Influence of Adhesion on Measured Runway Friction. [PDF]
Materials (Basel)Baimukhametov G, White G.
europepmc +1 more source
In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy
Advanced Engineering Materials, EarlyView.A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
The topology and electrical properties of nanoparticle networks
, 2014 Includes bibliographical references.The bulk and surface network topologies of milled silicon nanoparticle aggregates in layers deposited on porous and non-porous substrates have been quantitatively characterised using laboratory and synchrotron based ...
Jonah, Emmanuel Ohieku
core
Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)
Advanced Engineering Materials, EarlyView.Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho +8 more
wiley +1 more source
The effect of bullet yaw on the threat level : a numerical investigation [PDF]
It is well known that yaw can affect the penetrative power of armour piercing rounds. To investigate this effect purely experimentally is difficult because the typical ballistic set up does not allow control over the yaw angle of the projectile.
Landheer, D. +7 more
core
An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials
Advanced Engineering Materials, EarlyView.An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut +16 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley +1 more source
Advanced Engineering Materials, EarlyView.A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge +8 more
wiley +1 more source