Results 151 to 160 of about 1,613,587 (302)

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Flow Pattern Study and Pressure Drop Prediction of Two-Phase Boiling Process in Different Surface Wettability Microchannel. [PDF]

Micromachines (Basel), 2023
Zhang Y, Wu H, Zhang L, Yang Y, Niu X, Zeng Z, Shu B.   +6 more
europepmc   +1 more source

Pressure drop: securitising and de-securitising safeguarding [PDF]

, 2020
Finch, Jo, McKendrick, David
core  

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Influence of the Physical State of Microencapsulated PCM on the Pressure Drop of Slurry in a Circular Channel. [PDF]

Materials (Basel), 2022
Dutkowski K, Kruzel M, Kaczmarek D, Nalepa B, Zajączkowski B, Valíček J, Harničárová M.   +6 more
europepmc   +1 more source

Influence of Sample Preparation and Processing Procedures on the Thermal Diffusivity of MgO‐C Refractories

Advanced Engineering Materials, EarlyView.
The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan, Rhena Wulf, Till M. J. Stadtmüller, Christos G. Aneziris, Tobias M. Fieback   +4 more
wiley   +1 more source

A numerical simulation method for pressure drop and normal air velocity of pleated filters during dust loading. [PDF]

PLoS One, 2023
Teng G, Shi G, Shi G, Zhu J, Qi J.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Pressure Drop Dynamics during Filtration of Mixture Aerosol Containing Water, Oil, and Soot Particles on Nonwoven Filters. [PDF]

Polymers (Basel), 2023
Kamiński M, Gac JM, Sobiech P, Kozikowski P, Jankowski T.   +4 more
europepmc   +1 more source

Fundamental study of transpiration cooling [PDF]

Isothermal and non-isothermal pressure drop data and heat transfer data generated on porous 304L stainless steel wire forms, sintered spherical stainless steel powder, and sintered spherical OFHC copper powder are reported and correlated.
Benson, B. A., Dutton, J. L., Koh, J. C. Y.   +2 more
core   +1 more source