Results 141 to 150 of about 2,642,513 (283)

Raman Spectroscopic Identification of Oxide Phases in a Corroded MgO–Steel Composite Anode Used in Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler, Serhii Yaroshevskyi, Alexander Adamczyk, Mahnaz Mehdizadehlima, Julia Richter, Cameliu Himcinschi, David Rafaja, Alexandros Charitos, Christos G. Aneziris, Jens Kortus   +9 more
wiley   +1 more source

Prime and Primary Ideals

Indagationes Mathematicae (Proceedings), 1962
openaire   +2 more sources

Ideal Versus Actual Body Weight for Dosage of Sugammadex in Patients With Body Mass Index Less Than 18.5: A Randomized Controlled Trial. [PDF]

Cureus
Sato H, Uesaka T, Suzuki T, Iwasaki H.
europepmc   +1 more source

Interaction of MgO Recyclate‐Based Cermet Anode With KF‐AlF3‐Al2O3 at 800°C During Laboratory Scale Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain, Alexander Adamczyk, Felipe Alejandro Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Bulbospongiosus Muscle Flap for Repair of Rectal Injury During Penile Inversion Vaginoplasty. [PDF]

Plast Reconstr Surg Glob Open
Brydges HT, Eble DJ, Roblee CR, Koch G, Ettinger RE, Skokan AJ, Morrison SD.   +6 more
europepmc   +1 more source

Toward Low‐Consumable Anodes: Process Simulation and Prospective Life Cycle Assessment of NiFe2O4‐NiO‐Ni‐Cu vs. Prebaked Anodes for Aluminum Production with use of Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
Low‐consumable nickel ferrite‐based anodes for the Hall–Héroult process are compared with conventional prebaked carbon anodes using thermodynamic simulation and prospective life cycle assessment under contrasting future electricity system pathways from 2025 to 2050.
Felipe Alejandro Garcia Paz, Ulziikhuu Otgonbayar, Alexander Adamczyk, Farhan Hossain, Daniel Vogt, Johan Berg Pettersen, Alexandros Charitos   +6 more
wiley   +1 more source

American Heart Association's Life's Simple 7 for cardiovascular health assessment among Iranian adults: a national cross-sectional study from STEPwise approach to non-communicable diseases risk factor surveillance (STEPS) survey 2021. [PDF]

BMJ Open
Azadnajafabad S, Rezaei S, Almasi G, Ahmadi N, Golestani A, Rashidi MM, Abbasi-Kangevari M, Rezaei N, Rezaei N, Farzi Y, Ghasemi E, Yoosefi M, Haghshenas R, Nasserinejad M, Kazemi A, Abdolhamidi E, Saeedi Moghaddam S, Malekpour MR, Momen Nia Rankohi A, Djalalinia S, Farzadfar F.   +20 more
europepmc   +1 more source

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Professional nurses' perspectives on the influence of Ideal Clinic status on patient care quality in eThekwini, South Africa. [PDF]

Health SA
Mazibuko NN, Ngxongo TSP, Sokhela DG.
europepmc   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source