Results 131 to 140 of about 20,128 (231)

3D‐Printed Corneal Substitutes: Materials, Fabrication, and Preclinical Progress

Advanced Materials Technologies, EarlyView.
Successful clinical translation of 3D‐printed corneal substitutes relies on the interplay between the bioink properties, cellular component, and the fabrication process. These factors influence the critical properties of the construct, including optical transparency, mechanical stability, suture retention, that ultimately govern long‐term stromal ...
Shadi Moshayedi, Ashley Vazquez, Alexander J. Choi, Dimitrios Karamichos, Jayoung Kim   +4 more
wiley   +1 more source

Numerical evaluation on behavior of an integrated slope stabilization structure under seismic effect. [PDF]

Sci Rep
Wang Y.
europepmc   +1 more source

Nature‐Derived Chitosan Biopolymer: A Promising Candidate for Sustainable Electronics

Advanced Materials Technologies, EarlyView.
In the creation of environmentally friendly devices, nature‐derived chitosan biopolymer is a promising contender for sustainable electronic research. It can be utilized to create more ecologically friendly scalable gadgets and has a variety of uses in different active layers of electronics.
Joshua McDonald, Ali Nawaz, Amandeep Singh, Prashant Sonar   +3 more
wiley   +1 more source

The Influence of Certain Operating Conditions of the FDM Process on the Mechanical Properties of Polymeric Materials-A Review. [PDF]

Polymers (Basel)
Țisari V, Mihalache MA, Nagîț G, Ermolai V, Irimia AI, Grădinaru CG, Spiridon AA, Crăciun E, Hobjâlă RG, Slătineanu L.   +9 more
europepmc   +1 more source

Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications

Advanced Materials Technologies, EarlyView.
Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja, Mikko Kokkonen, Niina Halonen, Sami Myllymäki, Umair Rafique, Mandeep Singh, Ossi Laitinen, Heli Jantunen, Kristiina Oksman, Henrikki Liimatainen   +9 more
wiley   +1 more source

Transformation method of Φ-OTDR optical fiber strain and tunnel liner strain and its application in tunnel safety monitoring. [PDF]

Sci Rep
Cao K, Xie Z, Zhou F, Wang X, Tang J, Wang Z.   +5 more
europepmc   +1 more source

In Situ Two‐Dimensional Residual Stress Characterization of Thin Films

Advanced Materials Technologies, EarlyView.
An integrated in situ curvature metrology platform combining speckle‐based curvature optical metrology (SCOM) with multi‐beam optical sensors (MOS) enables spatially resolved two‐dimensional curvature mapping of thick sputtered coatings. The SCOM technique provides excellent agreement with MOS while providing an extended measurable curvature range ...
Wai Jue Tan, Wadwan Singhapong, Arindam Majhi, Chris Bowen, Alexander J.G. Lunt, Hongchang Wang, Kawal Sawhney   +6 more
wiley   +1 more source

Study on the adhesion performance of basalt fiber and polypropylene fiber based on unified phase-field theory and cohesive zone model. [PDF]

PLoS One
Wen Z, Simeng W, Huiming W, Guanghui C.
europepmc   +1 more source

Microfabrication of Soft Millirobots Propelled by Low Voltage Electrohydraulic Actuators

Advanced Materials Technologies, EarlyView.
Manual layer‐by‐layer assembly is replaced by wafer‐level MEMS batch fabrication for compliant polymer‐based electrohydraulic actuators. The microfabricated devices integrate sacrificially defined microcavities, Parylene‐C‐sealed inlets, and multilayer polymer–metal films.
Shai Shmulevich, Florian Hartmann, Herbert Shea   +2 more
wiley   +1 more source

Mechanical Behavior and Failure Modes of Cemented Backfill Under Impact Loading. [PDF]

Materials (Basel)
Zhang X, Yang Z, Li X, Liu F, Hou D, Zuo T, Wang J.   +6 more
europepmc   +1 more source