Results 1 to 10 of about 240,145 (341)

Impact Milling of Printed Circuit Board Waste for Resource Recycling and Evaluation of Liberation using Heavy Medium Separation [Translated]†

open access: diamondKONA Powder and Particle Journal, 2014
The authors evaluated the degree of liberation of printed circuit boards ground by impact milling to recover valuable materials. Wastes of two board types were ground with a swing-hammer-type impact mill.
Shigeki Koyanaka   +4 more
doaj   +3 more sources

Improved printed circuit board defect detection scheme [PDF]

open access: yesScientific Reports
In this paper, an improved printed circuit board(PCB)defect detection scheme named PD-YOLOv8 is proposed, which is specialized in the common and challenging problem of small target recognition in PCB inspection.
Lufeng Bai, Wen Hao Xu
doaj   +2 more sources

The current distribution in an electrochemical cell. Part VI: The quantitative treatment for cells with three plane parallel electrode arrangements [PDF]

open access: yesJournal of the Serbian Chemical Society, 2001
Amethod for the quantitative determination of the current density distribuion in cells with a three plane parallel electrode arrangement is proposed. It is shown that the current density distribution can be determined using the data obtained by ...
Popov K.I.   +2 more
doaj   +1 more source

The current distribution in an electrochemical cell. Part VII. Concluding remarks [PDF]

open access: yesJournal of the Serbian Chemical Society, 2002
Anew method for the determination of the ability of an electrolyte to distribute uniformly current density in an electrochemical cell is proposed. It is based on the comparison of the current in cells in which the electrode edges touch the cell side ...
Popov Konstantin I.   +2 more
doaj   +1 more source

Analysis of heating of printed circuit board conductors on a metal base for spacecraft devices at pulsed current

open access: yesФизика волновых процессов и радиотехнические системы, 2022
The article presents the results of the analysis of heating of printed circuit conductors of printed circuit boards mounted on a metal base, on-board device of spacecraft when pulsed current flows through them.
Alexey V. Kostin
doaj   +1 more source

Metal Recovery and Pb Removal by Melting Mixture of Lead Glass and Printed Circuit Board

open access: yesJournal of MMIJ, 2020
Reduction melting methods to remove Pb from lead silicate glasses such as cathode ray tube funnel glass have been extensively studied. In this paper, reduction melting of a model lead glass was conducted using printed circuit board as reductant.
Hiroyuki INANO   +3 more
doaj   +1 more source

RECYCLING OF PRINTED CIRCUIT BOARDS AIMING SILVER RECOVERY: A HYDROMETALLURGICAL ROUTE STUDY [PDF]

open access: yesTecnologia em Metalurgia, Materiais e Mineração, 2015
The aim of this paper is characterize printed circuit board of computers and propose a hydrometallurgical route for silver recovery present in its composition. Initially, the printed circuit board was comminuted in both knife and hammer mills.
Marcos Paulo Kohler Caldas   +4 more
doaj   +1 more source

Pyrolysis of Printed Circuit Boards [PDF]

open access: yesInternational Journal of Metallurgical Engineering, 2013
Printed Circuit Board (PCB) is an essential co mponent of almost all electrical and electron ic equip ments. The rapid growth of the use of such equipments has contributed enormously to the generation of large quantity of waste PCBs. The WPCBs not only contain valuable metals but also a large variety of hazardous materials.
Somnath Das   +3 more
openaire   +2 more sources

TECHNOLOGY FOR CREATING THE TOPOLOGY OF PRINTED CIRCUIT BOARDS USING POLYMER 3D MASKS

open access: yesСучасний стан наукових досліджень та технологій в промисловості, 2021
The subject of research is the influence of factors of exposure of two-dimensional images on the topology of conductors in the manufacture of printed circuit boards by the method of three-dimensional polymer photomasks.
Igor Nevliudov   +4 more
doaj   +1 more source

Increasing the accuracy of predicting the reliability of electronic equipment designs by improving models and calculation methods

open access: yesИзвестия высших учебных заведений. Поволжский регион:Технические науки, 2023
Background. The study of electronic equipment in the field of the impact of vibration load on it does not cease to be relevant for complex systems with high-speed electronic equipment.
E.T. Eskibaev   +5 more
doaj   +1 more source

Home - About - Disclaimer - Privacy