Results 21 to 30 of about 2,848,510 (315)
Evalaution and optimization of laser cutting parameters for plywood materials [PDF]
, 2013 Laser process parameters influence greatly the width of kerfs and quality of the cut edges. This article reports experiments on the laser plywood-cutting performance of a CW 1.5 kW CO2¬ Rofin laser, based on design of experiments (DOE).
Alrashed, K. +6 more
core +1 more source
Metals, 2021 In this study, thermo-mechanical simulation was conducted to predict thermal and stress behavior in Selective Laser Melting (SLM). Temperature-dependent material properties for processed material 304L stainless steel were incorporated into the model in ...
Lan Li, Frank Liou
doaj +1 more source
, 2020 Summary of deliverable D2.3. After the studies conducted at CNRS, the optimised composition was selected by the consortium for the HyCARE project, owing to its easy activation, good thermodynamics, kinetics, high reversible capacity at 55 °C and good cycling performances, as shown in Deliverable 2.2.
Dematteis, Erika Michela +2 more
openaire +1 more source
Effect of process parameters and optimization of CO2 laser cutting of ultra high performance polyethylene [PDF]
, 2010 The aim of this work is to relate the cutting edge quality parameters (responses) namely: upper kerf, lower kerf, ratio of the upper kerf to lower kerf and cut edge roughness to the process parameters considered in this research and to find out the ...
Olabi, Abdul-Ghani +2 more
core +1 more source
Relationships between LRI process parameters and impact and post-impact behaviour of stitched and unstitched NCF laminates [PDF]
, 2012 The general context of the development of out-of-autoclave processes in the aeronautics industry raises the question of the possible links between these new processes and impact behaviour. In this study, a Taguchi table was used in a design of experiment
Bouvet, Christophe +3 more
core +1 more source
MODEL OF OPTIMIZATION OF THE PARAMETERS OF THE DELIVERY PROCESS IN INTERNATIONAL TRAFFIC [PDF]
Scientific Journal of Silesian University of Technology. Series TransportThe efficiency of border crossing services depends on a number of parameters, including the scope of control activities, the number of vehicles to be serviced and the human resources involved.
Natalya SHRAMENKO +5 more
doaj +1 more source
Applied Sciences, 2020 Supercritical Water Gasification (SCWG) has the capacity to generate fuel gas effluent from wet biomass without previously having to dry the biomass. However, substantial efforts are still required to make it a feasible and competitive technology for ...
M. Belen García-Jarana +4 more
doaj +1 more source
Neurofuzzy approach to process parameter selection for friction surfacing applications [PDF]
, 2001 Friction surfacing is an advanced manufacturing process, which has been successfully developed and commercialised over the past decade. The process is used for corrosion and wear resistant coatings and for reclamation of worn engineering components.
Bedford, G.M +5 more
core +1 more source
Critical review of supercritical fluid extraction of selected spice plant materials
Macedonian Journal of Chemistry and Chemical Engineering, 2011 Supercritical fluid extraction (SFE) is one of the relatively new efficient separation method for the extraction of essential oils from different plant materials. The new products, extracts, can be used as a good base for the production of pharmaceutical
Milan N. Sovilj +2 more
doaj +1 more source
Parameter estimation in Manneville–Pomeau processes
Probability, Uncertainty and Quantitative Risk, 2023 In this work we study a class of stochastic processes $\{X_t\}_{t\in\N}$, where $X_t = (ϕ\circ T_s^t)(X_0)$ is obtained from the iterations of the transformation T_s, invariant for an ergodic probability μ_s on [0,1] and a continuous by part function $ϕ:[0,1] \to \R$. We consider here $T_s:[0,1]\to [0,1]$ the Manneville-Pomeau transformation.
Olbermann, Barbara P. +2 more
openaire +3 more sources