Results 1 to 10 of about 5,273 (117)
Process Window for Electron Beam Melting of 316LN Stainless Steel
Metals, 2021 Electron beam melting (EBM) is currently hampered by the low number of materials available for processing. This work presents an experimental study of process parameter development related to EBM processing of stainless steel alloy 316LN. Area energy (AE)
Stefan Roos, Lars-Erik Rännar
doaj +3 more sources
Nodule count effect on microstructure and mechanical properties of hypo-eutectic ADI alloyed with nickel [PDF]
Journal of Mining and Metallurgy. Section B: Metallurgy, 2021 Samples of ductile iron alloyed with 0.88 % Ni with a nodule count of 606, 523, and 290 nod/mm2 were obtained from sand cast plates of different thickness in the range from 8.46 to 25.4 mm.
Colin-García E. +5 more
doaj +1 more source
2017 17th International Conference on Application of Concurrency to System Design (ACSD), 2017 Peer ...
Mokhov, Andrey +2 more
openaire +2 more sources
IEEE Journal of the Electron Devices Society, 2022 Interconnect development for the new technology node requires coordinated efforts of multiple module teams working to co-optimize patterning and metallization solutions to meet performance and yield, and reliability targets.
Linrong Yang +17 more
doaj +1 more source
Development of a methodology for evaluating the process window of ductile machining for brittle-hard materials [PDF]
EPJ Web of Conferences, 2022 This paper presents a standardized methodology for determining the process window for ductile machining of brittle materials. Its application for CaF2 is reported, identifying an optimized process window for single-point diamond turning on UPM machines ...
Fähnle Oliver +5 more
doaj +1 more source
Window Processing of Binary Polarization Kernels [PDF]
IEEE Transactions on Communications, 2021 A decoding algorithm for polar (sub)codes with binary $2^t\times 2^t$ polarization kernels is presented. It is based on the window processing (WP) method, which exploits the linear relationship of the polarization kernels and the Arikan matrix.
Grigorii Trofimiuk, Peter Trifonov
openaire +2 more sources
Material Deformation Behavior in T-Shape Hydroforming of Metal Microtubes
Metals, 2020 In this study, the material behavior in the T-shape microtube hydroforming (MTHF) of pure copper and stainless-steel SUS304 microtubes with an outer diameter of 500 µm and wall thickness of 100 µm was examined experimentally and numerically ...
Hajime Yasui +4 more
doaj +1 more source
Improvement of process window for medium and thicker plates welded by K-TIG
工程科学学报, 2020 The welding of 8-mm thick Q235 low-carbon steel plates by keyhole tungsten inter gas welding (K-TIG), a deep penetration argon arc welding technique with tungsten electrode, is associated with many problems, including an unstable welding process and a ...
Tai WANG +5 more
doaj +1 more source
Extrusion Additive Manufacturing of PEI Pellets
Journal of Manufacturing and Materials Processing, 2022 The simplest, most cost-efficient, and most widespread Additive Manufacturing (AM) technology is Extrusion Additive Manufacturing (EAM). Usually, EAM is performed with filament feedstock, but using pellets instead of filaments yields many benefits ...
Matteo Fabrizio +3 more
doaj +1 more source
DFM: “Design for Manufacturing” or “Design Friendly Manufacturing”
Journal of Microelectronic Manufacturing, 2020 As the IC manufacturing enter sub 20nm tech nodes, DFM become more and more important to make sure more stable yield and lower cost. However, by introducing newly designed hardware (1980i etc.) process chemical (NTD) and Control Algorithm (Focus APC ...
Wenzhan Zhou, Hung-Wen Chao, Yu Zhang
doaj +1 more source