Results 131 to 140 of about 29,206 (304)
Intergranular corrosion of AISI 304L is analyzed, combining DLEPR test and AE. Slow scan rate polarization reveals time‐shifted and frequency‐dependent acoustic emission in the active region of the DLEPR curve, allowing a separation between passive oxide rupture, intergranular corrosion and pitting. ABSTRACT Intergranular corrosion (IGC) susceptibility
Alexander Kreisch +2 more
wiley +1 more source
This study explores the covalent functionalization of Ti3C2Tx using 5,5′‐bis(triisopropoxysilyl)‐2,2′‐bipyridine in different solvents, revealing that only m‐xylene enables effective covalent bonding, ensuring structural stability and preventing layer swelling.
Abelardo Sánchez‐Oliva +11 more
wiley +1 more source
Surface Locomotion of Cell‐Sized Microrobots Subject to Adhesive Heterogeneity
Chemically powered, cell‐sized microrobots exhibit translational, circular, or spiral motion through a balance among self‐phoretic propulsion, drag, gravity, and heterogeneous surface interactions. Experiments show that microrobot design and substrate conditions regulate both mobility and trajectory type.
Byung Ha Kang +3 more
wiley +1 more source
Conductance measurements demonstrate a fivefold enhancement in phase coherence length in a specially designed chiral polymer‐wrapped metallic single‐walled carbon nanotube (m‐SWNT) superstructure, relative to the corresponding achiral m‐SWNT benchmark.
Hanna T. Fridman +9 more
wiley +1 more source
Influence of Tapered-End and Round-End Bristle Designs on the Abrasive Enamel Wear Using Toothpastes With High Discrepancies in Abrasiveness. [PDF]
ABSTRACT Purpose The aim of this in vitro study was to investigate the influence of bristle end design of toothbrushes and the relative enamel abrasivity (REA) of used toothpaste on the resulting abrasive enamel wear. Materials and Methods A total of 160 bovine enamel samples were allocated into eight groups (n = 20) and surface topography was recorded
Stübi MS +5 more
europepmc +2 more sources
The influence of tool steel pretreatment on the running‐in behavior of TiNb‐diamond‐like carbon (DLC) coatings is investigated. Ion etching promotes carbide protrusion and increases coating roughness, while post‐deposition polishing reduces surface asperities.
Matěj Buřil +5 more
wiley +1 more source
Effect of Different Surface Treatments on Resistance to Abrasive Wear of AISI 4140 Steel
This study investigates how different surface treatments affect resistance to abrasive wear of AISI 4140 Steel. The wear rate was significantly higher in samples subjected to conventional treatments than in samples coated using the HVOF process, demonstrating the superior efficiency of coatings applied by thermal spraying in mitigating abrasive wear ...
Everton Freitas de Oliveira +3 more
wiley +1 more source
Abstract This in vitro study evaluated the effects of adding chitosan (Chi) to desensitizing agents applied before dental bleaching on enamel properties. Bovine enamel specimens were allocated to seven groups (n = 12): no treatment (negative control), 2% NaF (positive control), 2% NaF + 2% Chi, 2% NaF + 5% Chi, 2% NaF + 5% KNO3, 2% NaF + 5% KNO3 + 2 ...
Júlia Barbato +8 more
wiley +1 more source
Engineering Large-Grain Metal Halide Perovskite Films via Chemical Vapor Deposition for High-Performance, Ultralow-Noise Perovskite Photodetectors. [PDF]
Chemical vapor deposition produces large‐grain, phase‐pure CsPbBr3 films (grains up to 35 µm) with Drude‐like terahertz photoconductivity and twofold higher carrier mobility versus spin‐coated references. These microstructural advances translate into photodetectors with a detectivity of 8.4 × 1012 Jones, dark current below 1 pA cm−2, X‐ray sensitivity ...
Vanden Brande R +14 more
europepmc +2 more sources
Fibroblast and bacterial adhesion on a 3D‐printed polyetheretherketone‐based implant material
Abstract This study investigated fibroblast and bacteria proliferation on polyetheretherketone (PEEK)‐implant material 3D‐printed by fused deposition modeling (FDM) in comparison to titanium (cp‐Ti) and zirconia (ZrO2). Four groups were tested, including horizontally FDM‐printed PEEK (PH), vertically printed FDM‐PEEK (printed vertically [PV]), cp‐Ti ...
Rafaela Branco +6 more
wiley +1 more source

