Results 241 to 250 of about 190,046 (323)

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Exploring unsupervised feature extraction algorithms: tackling high dimensionality in small datasets. [PDF]

Sci Rep
Niu H, McCallum GB, Chang AB, Khan K, Azam S.   +4 more
europepmc   +1 more source

Enhanced Oxidation and Thermal Shock Resistance of N‐type Mg2Si0.89(Sn0.1,Sb0.01) Thermoelectric Material via Cr0.9Si0.1 Coating

Advanced Engineering Materials, EarlyView.
Cr0.9Si0.1 protective coatings are developed to enhance the thermal‐shock and oxidation resistance of Mg2Si0.89(Sn0.1,Sb0.01) thermoelectric (TE) materials. The coating forms a dense and adherent barrier that suppresses oxygen diffusion and mitigates mechanical degradation during cyclic oxidation, demonstrating its potential to improve the long‐term ...
Mikdat Gurtaran, Zhenxue Zhang, Xiaoying Li, Hanshan Dong   +3 more
wiley   +1 more source

Geometry and quantum brachistochrone analysis of multiple entangled spin-1/2 particles under all-range Ising interaction. [PDF]

Sci Rep
Amghar B, Yachi M, Amghar M, Almousa M, El-Latif AAA, Slaoui A.   +5 more
europepmc   +1 more source

Space Project SEE for Measuring G and its Possible Spatial and Time Variations

, 2001
V. N. Melnikov, Alvin J. Sanders
openalex   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Semantic Fusion Algorithm of 2D LiDAR and Camera Based on Contour and Inverse Projection. [PDF]

Sensors (Basel)
Yuan X, Liu Y, Xiong T, Zeng W, Wang C.
europepmc   +1 more source

Multiplications on projective spaces.

Michigan Mathematical Journal, 1969
openaire   +3 more sources

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Cyclic assisted cloning of arbitrary unknown single-particle states in amplitude damping channel. [PDF]

PLoS One
Maihemuti N, Aisan Y, Peng J, Wang Z, Tang J.   +4 more
europepmc   +1 more source