Results 141 to 150 of about 2,807,636 (295)
Indications and limits of prone position in ARDS
, 2015 Prone positioning, first proposed in 1974 and first applied in ARDS patients in 1976, results in improved arterial oxygenation in most patients. After the introduction of CT scanning, showing lung consolidation located in the dependent lung regions and ...
L. Gattinoni
core +2 more sources
Influence of Prone Position on the Survival of COVID-19 Patients Undergoing Invasive Mechanical Ventilation: A Propensity Score Matching Study [PDF]
Yuwei Zheng,1,* Chaochao Chen,1,* Xiaojie Bi,1,* Xiaowei Li,2 Jing Wang,1,3 Yufen Zheng,1,3 Yuan Yuan,1 Yongpo Jiang,4 Bo Shen,1,3 Yinghe Xu4 1Department of Clinical Laboratory, Taizhou Hospital of Zhejiang Province Affiliated to ...
Bi X +8 more
core
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
Fabrication Routes for Ionic Conducting Fiber Strain Sensors
Advanced Engineering Materials, EarlyView.Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw +3 more
wiley +1 more source
Ultrasound-guided central venous catheterization in prone position
Saudi Journal of Anaesthesia, 2010 Central venous catheterization (CVC) is a commonly performed intraoperative procedure. Traditionally, CVC placement is performed blindly using anatomic landmarks as a guide to vessel position.
Sofi Khalid, Arab Samer
doaj
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
Advanced Engineering Materials, EarlyView.Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová +6 more
wiley +1 more source
Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System
Advanced Engineering Materials, EarlyView.Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner +7 more
wiley +1 more source
A case of facial palsy after spinal surgery with prone positioning in a patient with achondroplasia
JA Clinical Reports, 2023 Shuto Yoshizawa +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.HEA interlayers offer a versatile route for joining high‐performance structural materials. Their compositional and structural design regulates interfacial reactions, suppresses brittle IMCs, and improves metallurgical bonding. Sandwich interlayers further integrate defect healing with precipitation strengthening, enabling improved strength–ductility ...
Lin Yuan +4 more
wiley +1 more source