Results 291 to 300 of about 128,209 (331)

Preparing Dental Hygiene Students to Care for Patients With Breast Cancer

Journal of Dental Education, EarlyView.
Denise M. Messina, Matthew J. Messina
wiley   +1 more source

Peer Review of Teaching to Enhance Faculty Experience and Outcomes

Journal of Dental Education, EarlyView.
Rebecca Henderson, Hiba A. Qari, Andréa G. Ferreira‐Zandoná   +2 more
wiley   +1 more source

Interim Maxillary Obturator Rehabilitation of an Aramany Class II Defect Following Resection for Oral Squamous Cell Carcinoma: A Case Report.

J Pharm Bioallied Sci
Sonkesriya S, Pugang T, Gupta A, Soni M, Maheshwari A, Shaikh S.   +5 more
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Electromechanical Design Handset Prosthesis

2020 Moscow Workshop on Electronic and Networking Technologies (MWENT), 2020
This paper describes the development and testing of an electromechanical hand prosthesis using feedback technology to compensate for lost tactile sensations partially, as well as how the device is controlled by neurointerface. In the course of this work, the following innovations, which distinguish this project from similar products of competitors ...
Artem Avdeev, Georgiy Klenevsky, Pavel Kolesnik   +2 more
openaire   +1 more source

Multifunctional hand prosthesis setup design

2016 Medical Technologies National Congress (TIPTEKNO), 2016
In this study, two channels, multifunctional myoelectric prosthesis hand is designed and operated for biomedical and control engineering departments laboratory as experiment apparatus. Various analog signal processing steps are implemented to the surface EMG signals which received on the triceps and biceps muscles.
Celik, Mehmet Serdar, Tepe, Cengiz, Bas, Hasan, Eminoglu, Ilyas   +3 more
openaire   +2 more sources

Topological optimization in hip prosthesis design

Biomechanics and Modeling in Mechanobiology, 2009
With particular interest on total hip arthroplasty (THA), optimization of orthopedic prostheses is employed in this work to minimize the probability of implant failure or maximize prosthesis reliability. This goal is often identified with the reduction of stress concentrations at the interface between bone and these devices.
FRALDI, MASSIMILIANO, L. Esposito, G. Perrella, A. Cutolo, S. C. Cowin   +4 more
openaire   +4 more sources

Design of an Intervertebral Disc Prosthesis

Spine, 1991
This article presents criteria for the design of a lumbar intervertebral disc prosthesis that take into consideration issues of endurance, materials behavior, geometry, kinetics, motion constraints, fixation to bone, and safety. The criteria and design philosophies discussed are generally applicable in the synthesis of any new implant system ...
T P, Hedman, J P, Kostuik, G R, Fernie, W G, Hellier   +3 more
openaire   +2 more sources

Composite hip prosthesis design. I. Analysis

Journal of Biomedical Materials Research, 1998
An investigation was performed to study the mechanical performance of fiber-reinforced composite hip prostheses in a femur. The main objective of the study was to evaluate the effect of fiber orientation of a composite femoral implant on the response of the surrounding femoral bone.
H, Yildiz, S K, Ha, F K, Chang
openaire   +2 more sources

Composite hip prosthesis design. II. Simulation

Journal of Biomedical Materials Research, 1998
An investigation was performed to study the mechanical performance of fiber-reinforced composite hip prostheses. In Part I of the study, a three-dimensional finite element code was developed for analyzing a composite hip prosthesis in a femur. The material properties of the composite were treated as anisotropic and inhomogeneous while the properties of
H, Yildiz, F K, Chang, S, Goodman
openaire   +2 more sources