Results 31 to 40 of about 12,247 (201)
FEM and Von Mises analysis on prosthetic crowns structural elements: evaluation of different applied materials [PDF]
, 2017 The aim of this paper is to underline the mechanical properties of dental single crown prosthodontics materials in order to differentiate the possibility of using each material for typical clinical condition and masticatory load.
Cesare, D’Amico +10 more
core +1 more source
Flexural Strength of Composite Based Provisional Crown Materials
International Journal of Innovative Research in Medical Science, 2021 Introduction: One of the important aspects of provisional restorations, especially in case of long-span edentulous situations, short-height pontics, extended treatment time and in patients with para-functional habits is their flexural strength. Maintaining the integrity of the provisional restorations throughout the course of treatments is highly ...
null Osama Qutub +2 more
openaire +2 more sources
Provisional Crown Failures in Dental School Predoctoral Clinics
Journal of Dental Education, 2007 Following a preliminary study indicating that at least 10 percent of single‐unit crown temporary restorations failed in patients who received treatment by predoctoral students, a comprehensive examination of provisional crown failure was initiated to identify strategies to reduce the failure rate.
Jeffrey D, Hyde +2 more
openaire +3 more sources
3D PRINTING – AN ALTERNATIVE OF CONVENTIONAL CROWN FABRICATION: A CASE REPORT [PDF]
Journal of IMAB, 2018 The present paper is a case report of prosthetic treatment built upon 3D technologies for manufacturing of dental restorations. The case shows laboratory protocol of 3D printed full coverage provisional crowns and cast patterns for press ceramic crowns ...
Iveta Katreva +2 more
doaj +1 more source
Influence of Matrix Type on Surface Roughness of Three Resins for Provisional Crowns and Fixed Partial Dentures [PDF]
, 2017 Purpose: This study evaluated the effect of matrix type on the surface roughness of resins for provisional crowns and fixed partial dentures. Materials and methods: Ninety specimens of two acrylic resins (Trim II, Tab2000) and one bis-acryl composite ...
Ayuso Montero, Raúl +4 more
core +1 more source
Optical properties of monolithic zirconia crowns: In vitro and In vivo evaluation [PDF]
Balkan Journal of Dental Medicine, 2022 Background/Aim: The aim of this study was to compare the monolithic and layered zirconia crowns by their optical property of translucency, using in vitro and in vivo evaluation methods. Material and Methods: One upper incisor and one canine were prepared
Koci Brunilda, Dedaj Edlira, Koci Nazmi
doaj +1 more source
Removal of failed crown and bridge [PDF]
, 2012 Crown and bridge have life span of many years but they fail for a number of reasons. Over the years, many devices have been designed to remove crowns and bridges from abutment teeth.
Poduval, Soorya T. +3 more
core +1 more source
Clinical and Experimental Dental Research, 2023 Objective The aim of this in vitro study was to compare the effect of printing layer thickness on the marginal and internal fit of interim crowns. Material and methods A maxillary first molar model was prepared for ceramic restoration.
Mahya Hasanzade +3 more
doaj +1 more source
The "TORONTO PROSTHESIS", an appealing method for restoring patients candidates for hybrid overdentures: a case report [PDF]
, 2012 The implant is a therapeutic resource in constant evolution, and the different types of implants and techniques have been increasingly used in cases of both fully or partially edentulous patients. In some cases they provide more conservative treatment,
Albaladejo Martínez, Alberto +2 more
core +1 more source
Contemporary Clinical Dentistry, 2015 Purpose: The purpose of this in vitro study was to evaluate and compare the primary marginal accuracy of four commercially available provisional materials (Protemp 4, Luxatemp Star, Visalys Temp and DPI tooth moulding powder and liquid) at 2 time ...
Bhavya Mohandas Amin +2 more
doaj +1 more source