Results 181 to 190 of about 50,323 (213)

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Biomechanical Investigations of a New Model Graft Attachment to Distal Phalanx in Two-Stage Flexor Tendon Reconstruction. [PDF]

J Clin Med
Mazurek T, Żerdzicki K, Napora J, Ceynowa M.   +3 more
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Interfacial Pull-Out Properties of Surface-Grown Carbon Nanotubes (gCNTs) on Para-Aramid Fabric Material by Chemical Vapor Deposition (CVD). [PDF]

Nanomaterials (Basel)
Bilisik E, Korkmaz M, Bilisik K.
europepmc   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Screw Withdrawal Resistance from WPC Profiles Used in Door Frame Production. [PDF]

Materials (Basel)
Potok Z, Kwidziński Z, Pędzik M, Wiaderek K, Prałat B, Rogoziński T.   +5 more
europepmc   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Unraveling and Sliding of Polypeptide Strands Underlies the Exceptional Toughness of the Triple-Helix Collagen Molecule. [PDF]

ACS Nano
Rohatschek A, Zappone B, Steinbauer P, Rufin M, Barrágan Rivera DA, De Santo MP, Andriotis OG, Baudis S, Thurner PJ.   +8 more
europepmc   +1 more source

A Krackow-based suture technique as a novel alternative for feline patellar fracture repair: a biomechanical comparison. [PDF]

J Feline Med Surg
Kim MY, Jeong ES, Lee S, Kim HY.
europepmc   +1 more source

An open-source test stand for backlash measurement in low-cost UART servo motors. [PDF]

HardwareX
Kotov B.
europepmc   +1 more source