Results 111 to 120 of about 6,861,533 (339)
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Research and design of pulse wave sphygmomanometer based on RNN
Dianzi Jishu Yingyong, 2018 Aiming at the inconvenience and discontinuity of traditional cuff sphygmomanometer, a portable pulse wave sphygmomanometer is designed. The sphygmomanometer collects the pulse wave signal of the finger end through the photoelectric sensor，preprocesses ...
Liu Yanping, Li Jie, Jin Fei
doaj +1 more source
A piezo-bar pressure probe [PDF]
, 1967 Piezo-bar pressure type probe measures the impact velocity or pressure of a moving debris cloud. It measures pressures up to 200,000 psi and peak pressures may be recorded with a total pulse duration between 5 and 65 ...
Friend, W. H. +2 more
core +1 more source
Detonation Tube Impulse in Subatmospheric Environments [PDF]
, 2006 Thrust from a multicycle pulse detonation engine operating at practical flight altitudes will vary with surrounding environment pressure.We have carried out the first experimental study using a detonation tube hung in a ballistic pendulum arrangement ...
Cooper, M., Shepherd, J. E.
core +1 more source
Advanced Engineering Materials, EarlyView.High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin +4 more
wiley +1 more source
Pulse Pressure and Diabetic Eye Disease
Journal of the American Heart Association: Cardiovascular and Cerebrovascular Disease, 2019 See Article Yamamoto et ...
Anthony M. Dart
doaj +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Critical Care, 2013 IntroductionSeveral single-center studies and meta-analyses have shown that perioperative goal-directed therapy may significantly improve outcomes in general surgical patients.
C. Salzwedel +10 more
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source