Results 1 to 10 of about 19,869 (147)

Improvement of the Method for Fixing a Punch in the Punch Holder [PDF]

open access: yesApplied Sciences, 2021
The punching process allows large quantities of parts to be produced at very low cost. This paper studies how the technique used for fixing a punch can be improved in order to increase productivity before punch fracture, which results in large numbers of parts failing to be produced, thus creating a significant shortfall.
Semaan, Melissa   +3 more
openaire   +2 more sources

The calibration of NLFE model for the assessment of the maximum punching capacity of flat slabs [PDF]

open access: yesMATEC Web of Conferences, 2023
The requirements on structural engineers to design more subtle flat slabs are still increasing and therefore they must often design a large amount of reinforcement against punching. The maximum amount of transverse reinforcement is limited by the maximum
Gregusova Natalia, Halvonik Jaroslav
doaj   +1 more source

Strength of cast-in-place slabs for rectangular cross-section columns punching [PDF]

open access: yesE3S Web of Conferences, 2021
Flat slabs in contemporary buildings are most commonly supported by rectangular cross-section columns. Research of slabs supported by rectangular cross-section columns for punching is rather narrow.
Istomin Andrey, Kudryavtsev Maksim
doaj   +1 more source

Progressive Collapse Analysis Of Flat Slab Buildings With Post-Punching Effect [PDF]

open access: yesمهندسی عمران شریف, 2021
The reinforced concrete flat slab is one of the types of floor systems used to construct residential, office and parking buildings. Because of the direct transfer of floor loads to columns, flat slabs are susceptible to punching failure in slab-column ...
E. Mousapoor, V. Ghiasi, R. Madandoust
doaj   +1 more source

Evaluation of Localized Necking Models for Fracture Prediction in Punch-Loaded Steel Panels

open access: yesJournal of Marine Science and Engineering, 2021
This study compared the experimental test results on punch-loaded unstiffened and stiffened panels with numerical predictions using different localized necking modeling approaches with shell elements.
Burak Can Cerik   +2 more
doaj   +1 more source

Experimental analysis of concrete flat slabs with internal stud-type shear reinforcement [PDF]

open access: yesRevista IBRACON de Estruturas e Materiais, 2023
This study evaluates seven flat slabs made with reinforced concrete. There are three reference slabs, one of them doesn’t present any shear reinforcement.
Diego Borja Ferreira   +4 more
doaj   +1 more source

Research on Optimization of Large Flow Hydraulic Punching Process in Zhaozhuang Mine

open access: yesGeofluids, 2022
Taking hydraulic punching test of Zhaozhuang Mine as engineering background, by comparing the field application effects of different hydraulic punching processes, the relationship between coal moisture content around the borehole blockage and gas ...
Jiabao Zhang, Dingqi Li
doaj   +1 more source

Study and application of reasonable parameters for hydraulic punching of layer penetration boreholes in Changping Coal Mine

open access: yesEnergy Science & Engineering, 2023
Aiming at the application of hydraulic punching technology in soft, low permeability, and high gas coal seams in Changping Coal Mine, there are problems such as large workload, poor permeability enhancement effect, and the formation of “blank zones” in ...
Rui Min   +4 more
doaj   +1 more source

Punching Shear Strength of Voided Slab: Literature Review and Evaluation of Design Codes

open access: yesWasit Journal of Engineering Sciences, 2022
Despite of the economic advantages provided by the voided slabs, their design against punching shear failure, as suggested by the current building codes, are based on the equations derived from tests on flat slabs.
Akram mohammad, Ahmed Al-Bayati
doaj   +1 more source

Home - About - Disclaimer - Privacy