Results 231 to 240 of about 858,504 (314)

Effect of Process Parameters on Friction Properties of AISI 304 Steel Sheet during Strip Drawing Test

steel research international, EarlyView.
This study investigates how drawing process parameters affect the tribological behavior of AISI 304 steel sheet. Under lubricated conditions, increasing normal force, drawing speed, and countersamples roughness reduces the coefficient of friction by up to 21%.
Felipe de Souza Leal, Anderson Júnior dos Santos, Cláudio Moreira de Alcântara, Wilian da Silva Labiapari, Valmir Dias Luiz, Tomasz Trzepieciński, Jorge Luis Coleti   +6 more
wiley   +1 more source

Improving the punching capacity of footings using geocell, geogrid and granular soil replacement. [PDF]

Sci Rep
Ebid AM, Abdelhamid NM, Zaher AH, Ors DM.   +3 more
europepmc   +1 more source

Enhancing Cycling Stability of All‐Solid‐State Batteries With 3D‐Architectured Interfaces via Controlled Yield Stress and Internal Stress Relaxation

Small Structures, EarlyView.
3D interfacial architectures are introduced into all‐solid‐state batteries (ASSBs) to enhance cycling stability under low‐pressure conditions. The 3D interfaces relax internal stress and suppress resistance accumulation during long‐term operation. Integrated structural and electrochemical analyses reveal that 3D interfaces provide continuous contact ...
Hyeseong Jeong, Junyoung Park, Baik Jin Kim, Dongwook Shin, Jong‐Ho Lee, Sung Soo Shin, Hyoungchul Kim   +6 more
wiley   +1 more source

Gas permeability characteristics of the hanging wall and footwall in normal faults based on true triaxial experimental system. [PDF]

Sci Rep
Song W, Yan L, Jiao H.
europepmc   +1 more source

Punching shear and load-deflection performance of RC flat slab made with hybrid concrete

Mustafa Hamid Jasim, Shereen Qasim Abdulridha, Ammar Ali Hussein, Mohammed Salah Nasr, Ali Shubbar   +4 more
openalex   +1 more source

Strip loading in reinforced concrete: Mechanical modeling and experimental validation

Structural Concrete, EarlyView.
Abstract Strip loading of reinforced concrete is a common problem in engineering practice. The concrete compressive strength at the load introduction can be several times higher than the uniaxial concrete compressive strength, which can be attributed to geometrical and passive confining stresses caused by load dispersion and reinforcement, respectively.
Fabian Morger, Albin Kenel, Walter Kaufmann   +2 more
wiley   +1 more source

The mechanism of permeability enhancement of coal seams by hydraulic fracturing based on the characterization of coal physical properties. [PDF]

Sci Rep
Zhao X, Zhao D, Nie B, Liu X, Liu P, Wang M, Hu B, Li H, Deng C, Duan Z.   +9 more
europepmc   +1 more source

Punching shear failure of reinforced concrete slabs: FEM-based analysis of concrete–steel interface degradation and fracture mechanisms

Fernando Suárez, Jaime C. Gálvez
openalex   +1 more source

Punching shear in flat slab systems – Experimental quantification of unconsidered system influences

Structural Concrete, EarlyView.
Abstract Due to the demand for slender and functional buildings, flat slabs are a frequently used load‐bearing element in buildings. However, the concentrated load introduction at the slab‐column connection is often the governing detail in design due to punching shear failure.
Matthias Kalus, Jan Ungermann, Martin Classen, Josef Hegger   +3 more
wiley   +1 more source

Punch Edge Topological Design for Reduction of Work Hardening Damage in Shearing of Non-Oriented Electrical Steel Sheets. [PDF]

Materials (Basel)
Okada R, Ito K, Funazuka T, Aizawa T, Shiratori T.   +4 more
europepmc   +1 more source