Results 91 to 100 of about 1,110,073 (243)

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

Reduction of Oxide Inclusions During the High‐Frequency Welding of Steel via a Nonthermal Ar/H2 Plasma Jet

Advanced Engineering Materials, EarlyView.
High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin, Lienhard Wegewitz, René Gustus, Henning Wiche, Wolfgang Maus‐Friedrichs   +4 more
wiley   +1 more source

Piezoresistive Monitoring of Carbon Nanomaterial‐Reinforced Epoxy Composites Under Cyclic and Fatigue Loading: A Review

Advanced Engineering Materials, EarlyView.
Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente, J. Nunes‐Pereira, A. P. Silva, P. N. B. Reis   +3 more
wiley   +1 more source

The Renaissance of Qualitative Methods

Forum: Qualitative Social Research, 2005
Even though qualitative research was first done more than a century ago, the first texts that tried to define its methodology appeared only eighty years later, in the late sixties. This article explores the reasons why there was such a long delay and why
Giampietro Gobo
doaj  

Nanoindentation Criteria for Combinatorial Thin Film Libraries

Advanced Engineering Materials, EarlyView.
Thin‐film material libraries are compositional spreads used for screening composition‐structure‐property relationships. Nanoindentation is often used to characterize mechanical behavior across these systems, however variations in methodology are widespread.
Andre Bohn, Adie Alwen, Andrea M. Hodge
wiley   +1 more source

Qualitative Methods in Israel

Forum: Qualitative Social Research, 2005
This paper surveys the evolution and cur­rent state of the art of qualitative methods as an academic discipline in Israel. By means of a survey carried out especially for this issue of FQS, the paper documents the prevalence of qualitative courses in ...
Shalva Weil
doaj  

3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs

Advanced Engineering Materials, EarlyView.
This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu, Nelson Pereira, Javier Vicente, Carmen Rial Tubio, Senentxu Lanceros‐Méndez   +4 more
wiley   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source