Results 201 to 210 of about 54,781,618 (350)

Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories

open access: yesAdvanced Engineering Materials, EarlyView.
Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter   +5 more
wiley   +1 more source

A qualitative study of telemedicine in heart failure care. [PDF]

open access: yesFront Med (Lausanne)
Micheluzzi V   +12 more
europepmc   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

open access: yesAdvanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios   +5 more
wiley   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal   +2 more
wiley   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

open access: yesAdvanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena   +2 more
wiley   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff   +9 more
wiley   +1 more source

Qualitative Study on Vaccinations for Travelers. [PDF]

open access: yesVaccines (Basel)
Nuccetelli F   +5 more
europepmc   +1 more source

Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions

open access: yesAdvanced Engineering Materials, EarlyView.
This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel   +6 more
wiley   +1 more source

Investigation of Oxygen‐Free Wetting Behavior of Aluminum on Copper via Molecular Dynamics Simulations and Experiments

open access: yesAdvanced Engineering Materials, EarlyView.
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu   +8 more
wiley   +1 more source

Home - About - Disclaimer - Privacy