Results 161 to 170 of about 643,214 (199)

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

Cost-effectiveness of angiographic quantitative flow ratio-guided coronary intervention: A multicenter, randomized, sham-controlled trial. [PDF]

Chin Med J (Engl)
Zhao Y, Guan C, Wang Y, Jin Z, Yu B, Fu G, Chen Y, Guo L, Qu X, Zhang Y, Dou K, Wu Y, Yang W, Tu S, Escaned J, Fearon WF, Qiao S, Cohen DJ, Krumholz HM, Xu B, Song L, FAVOR III China Study Group.   +21 more
europepmc   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

Quantitative flow ratio will supplant wire-based physiological indices: pros and cons. [PDF]

EuroIntervention
Holm NR, Andersen BK, Götberg M.
europepmc   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Anticorrosive Performance of Smart Epoxy Coatings With Poly(urea‐formaldehyde) Microcapsules Filled With 5‐Ethylidene‐2‐norbornene

Advanced Engineering Materials, EarlyView.
PUF/ENB microcapsules were synthesized based on a sequential factorial design and incorporated into an epoxy matrix. Their anticorrosive action, associated with the self‐healing mechanism, demonstrated that the addition of microcapsules to the coating improved anticorrosive performance compared to pure epoxy coatings, particularly when the encapsulate ...
Vandicleya Alves Moreira, Maria Paula de Carvalho Freire, Ygor Matheus Pereira de Paula, Ana Leticia Santos, Alice da Costa Silva, Nicolau Apoena Castro, Maria Carolina Burgos Costa   +6 more
wiley   +1 more source

Publisher Correction: Quantitative flow ratio or angiography for the assessment of non-culprit lesions in acute coronary syndromes, a randomized trial. [PDF]

Clin Res Cardiol
Ullrich-Daub H, Olschewski M, Schnorbus B, Belhadj KA, Köhler T, Vosseler M, Münzel T, Gori T.   +7 more
europepmc   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Outcomes from Quantitative Flow Ratio-Guided Complete Revascularization and Angiography-Guided Percutaneous Coronary Intervention in Patients with ST-Segment Elevation Myocardial Infarction. [PDF]

Med Sci Monit
Krivickas Ž, Barauskas M, Jodka N, Žiubrytė G, Pranevičius R, Unikas R.   +5 more
europepmc   +1 more source

Influence of Particle Shape and Size in Copper‐Based Low‐Temperature Metallization Paste for Solar Cells

Advanced Engineering Materials, EarlyView.
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi, M. N. Wengenmeyr, J. Bartsch, B. E. Rapp   +3 more
wiley   +1 more source