Results 11 to 20 of about 7,132 (177)

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Low Cycle Repetitive Loading of Ti‐6Al‐4V‐Epoxy Composite Lattice Structures for Enhanced Energy Dissipation and Damage Tolerance

Advanced Engineering Materials, EarlyView.
Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon, Jordan Noronha, Justin Dirrenberger, Andrey Molotnikov   +3 more
wiley   +1 more source

Influence of Geometric Design on Mechanical Performance of Auxetic Metastructure

Advanced Engineering Materials, EarlyView.
Strategic geometric reinforcement transforms auxetic performance. This study evaluates 3D‐printed arrowhead metastructures, revealing that a modified design with local ring reinforcement suppresses premature failure to achieve superior energy absorption and structural efficiency.
Muhammad Gulzari, Supharoek Sornsomrit, Muhammad Ayaz Akbar, Stephan Rudykh   +3 more
wiley   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Grain Refinement During Severe Plastic Deformation and Similitude of Subgrain Formation: A Molecular Dynamics Study

Advanced Engineering Materials, EarlyView.
Molecular dynamics is used to investigate structure refinement during severe plastic deformation. The results show similitude with experimental data. Molecular dynamics simulations of severe plastic deformation of monocrystalline and polycrystalline samples by multiaxial compression of aluminum are carried out.
Roberto B. Figueiredo
wiley   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source