Results 91 to 100 of about 105,726,892 (209)

A Review of Footstep Energy Harvesting Systems

IEEE Access
Recently, energy harvesting through human locomotion has emerged as a promising source of clean energy for fueling low-power smart electronic devices.
Kritesh A. Chandra, Sumesh Narayan, Kabir A. Mamun, Aneesh A. Chand, Deepak Prasad, Mohammed Rafiuddin Ahmed   +5 more
doaj   +1 more source

RESEARCH ON GEAR TOOTH INTERFERENCE PROBLEM OF SINGLE DRIVE MULTI-POINT MESHING RACK AND PINION TRANSMISSION

Jixie qiangdu
The load capacity of the rack and pinion mechanism is limited by the contact strength of the gear tooth surface.In order to improve its load capacity,multiple pairs of gears and single rack meshing were adopted.In order to simplify the structure of the ...
doaj  

MODELING AND VALIDATION OF SIX-BAR RACK AND PINION STEERING LINKAGE SYSTEM [PDF]

, 2012
A vehicle handling behavior is much influenced by the performance of steering system and its mechanism. Steering linkage play a very important role in maneuvering of a vehicle.
Amir, Mohd Zubir, ABDULLAH, Mohd Azman, Hudha, Khisbullah, Hassan, Muhammad Zahir, Mohammad Nasir, Mohd Zakaria   +4 more
core  

Simulasi dan analisis sistem penggerak pembangkit listrik tenaga gelombang laut (PLTGL) tipe rack gear and pinion menggunakan solidwork [PDF]

, 2020
Permintaan pasokan energi listrik yang terus meningkat. Menyebabkan perlunya upaya untuk mengembangkan potensi energi alternatif, terutama energi terbarukan yang ramah dan akrab lingkungan.
Nova Roliana, (NIM. 1011511042)
core  

Effects of gear manufacturing errors on rack and pinion steering meshing

, 2017
In the present paper the effects of rack manufacturing errors on the meshing of crossed helical rack and pinion are analyzed. The study is performed using multibody simulations that include the effects of the forces acting at the gear mesh to determine ...
Piantoni A., Tabaglio L., Pellicano F., Marano D., Barbieri M., Lucchi M.   +5 more
core  

Experimental Study on the Effect of the Rack Structure on the Hydrodynamic Characteristics of Truss-type Leg

Shiyou jixie, 2019
The rack and pinion system is the most commonly used lifting system for jack-up offshore platforms. There are relatively few studies on the influence of rack structure on the hydrodynamic characteristics of truss-type legs.
Li Xiangkun, Xie Yingchun, Liu Guijie, Tian Xiaojie   +3 more
doaj  

Modification Method and Performance Analysis of Automobile Steering Rocker Shaft Non-circular Gear Sector

Jixie chuandong, 2017
The transmission performance of the recirculating ball steering is closely related to the tooth profile shape of the rocker shaft non-circular gear sector.
Ding Guolong, Yu Jinfang, Ming Tingbo, Zhang Yali   +3 more
doaj  

Research on three-dimensional parametric solid modeling method of variable modulus non-standard rack

Jixie chuandong
ObjectiveIn order to solve the problem that the gear rack of automobile steering gear cannot be modeled directly and the repetitive work is too much, a three-dimensional parametric modeling method based on SolidWorks software secondary development was ...
DING Guolong, WANG Anyu, WANG Zhifan, XUE Leigang   +3 more
doaj  

Lehigh Coal and Navigation Company Records - Item 1422: Plan of Rack and Pinion, Single Stem, Gate Lift Device

, 1911
Full date of technical drawing: November 14, 1911. This schematic shows a standard plan of a rack and pinion, single stem, gate lift device made using cast iron.

core  

A Small-Scale Hopper Design Using a Power Spring-Based Linear Actuator. [PDF]

Biomimetics (Basel), 2023
Yang SG, Lee DJ, Kim C, Jung GP.
europepmc   +1 more source