Results 141 to 150 of about 160,000 (315)
Advanced Engineering Materials, EarlyView.This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca +9 more
wiley +1 more source
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, EarlyView.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source
, 2017 This article outlines a compact annular-radial-orifice flow magnetorheological valve through theoretical calculation, simulation analysis and experiment verification.
Mingke Liao (20243385) +2 more
core
Advanced Engineering Materials, EarlyView.A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi +3 more
wiley +1 more source
Numerical modelling of viscous turbomachinery flows with a pressure correction method [PDF]
, 1992 A fully elliptic computational method for the analysis of steady viscous flow in high speed subsonic centrifugal compressor impellers with tip leakage, is presented.
Tourlidakis, A.
core
Advanced Engineering Materials, EarlyView.Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş +2 more
wiley +1 more source
Estudo numerico da estabilidade hidrodinamica em escoamentos radiais [PDF]
, 1992 Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro TecnologicoO problema de estabilidade linear em difusores radiais é abordado numericamente através do método dos volumes finitos, utilizando uma adapação do esquema proposto por ...
Oliveira, Jáuber Cavalcante de
core
Advanced Engineering Materials, EarlyView.Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink +4 more
wiley +1 more source
Effects of aggregation on the blood flow velocity field measured by a μPIV based technique
, 2009 This paper was presented at the 2nd Micro and Nano Flows Conference (MNF2009), which was held at Brunel University, West London, UK. The conference was organised by Brunel University and supported by the Institution of Mechanical Engineers, IPEM, the ...
2nd Micro and Nano Flows Conference (MNF2009) +3 more
core
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source