Results 81 to 90 of about 160,269 (292)

Initial radio-frequency gas heating experiments to simulate the thermal environment in a nuclear light bulb reactor [PDF]

open access: yes
Initial radio frequency gas heating experiments to simulate thermal environment in nuclear light bulb ...
Kendall, J. S.   +2 more
core   +1 more source

Heating of trapped ions from the quantum ground state [PDF]

open access: yes, 2000
We have investigated motional heating of laser-cooled 9Be+ ions held in radio-frequency (Paul) traps. We have measured heating rates in a variety of traps with different geometries, electrode materials, and characteristic sizes.
Itano, W. M.   +11 more
core   +2 more sources

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal   +2 more
wiley   +1 more source

Radio Frequency Heating: Assessing Its Viability for Composite Tape Processing Line

open access: yesIEEE Access
This paper assesses the potential of radio frequency (RF) heating as a non-contact, low-power, and localised volumetric heating method for carbon fibre reinforced polymer (CFRP) composite tape processing, with a view toward integration into a larger ...
Hanisa Hasrin   +8 more
doaj   +1 more source

Kinetic simulation of the sheath dynamics in the intermediate radio-frequency regime

open access: yes, 2013
The dynamics of temporally modulated plasma boundary sheaths is studied in the intermediate radio frequency regime where the applied radio frequency and the ion plasma frequency are comparable.
Brinkmann, R. P.   +8 more
core   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

open access: yesAdvanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi   +2 more
wiley   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff   +9 more
wiley   +1 more source

Comparison of Different Electricity-Based Thermal Pretreatment Methods for Enhanced Bioenergy Production from Municipal Sludge

open access: yesMolecules, 2018
This paper presents results for a comprehensive study that compares the performance of three electricity-based thermal pretreatment methods for improving the effectiveness of anaerobic digestion (AD) to process municipal wastewater sludge.
E. Hosseini Koupaie   +2 more
doaj   +1 more source

Ionosphere/microwave beam interaction study [PDF]

open access: yes
A solar power satellite microwave power density of 20mw sq cm was confirmed as the level where nonlinear interactions may occur in the ionosphere, particularly at 100 km altitude.
Duncan, L. M., Gordon, W. E.
core   +1 more source

Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties

open access: yesAdvanced Engineering Materials, EarlyView.
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat   +7 more
wiley   +1 more source

Home - About - Disclaimer - Privacy