Results 261 to 270 of about 5,632,412 (295)
Some of the next articles are maybe not open access.
Surface analysis of corrugated rail treads
Wear, 1990Abstract Corrugated rail treads were examined by surface analysis. The results led to the conclusion that the vibration of the wheel-tread system leads to different amounts of load at different areas of the surface. As a consequence there are areas with higher loads, higher deformation, higher hardening and higher wear resistance: the “hills ...
H.G. Feller, K. Walf
openaire +1 more source
A possible origin of surface cracks in rails
Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit, 2011The deformation and stress state due to overrolling near the rough surface of a rail is studied. Then a criterion for the inclination of a shear localization zone (SLZ) is introduced. Furthermore, the recent finding that the crack tip driving forces becomes infinite for a crack embedded in a SLZ is recalled. Experimental observation shows also that the
F D Fischer, W Daves
openaire +1 more source
Some comments on surface cracks in rails
Fatigue & Fracture of Engineering Materials & Structures, 2006ABSTRACTThe present work considers the problem of whether a shallow angle surface crack on a rail may propagate either parallel or perpendicular to the surface. After referring to a classification of crack‐like defects, a distinct surface crack with a typical length of 1 mm and more, inclined to the surface by an angle of approx.
F. D. FISCHER +3 more
openaire +1 more source
Traction, curving and surface damage of rails, Part 2: Rail damage
Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit, 2014The tangential forces on a rail resulting from a combination of traction and curving are considered. These forces are a significant component of both wear and shakedown. These two simple mechanisms can be used to understand most types of damage that occur on both rails and wheels.
openaire +1 more source
Microscopic investigation of surface layers on rails
Applied Surface Science, 2005Reflection γ-ray and conversion electron Mossbauer spectroscopy (MS) completed by optical (OM), transmission electron (TEM) and atomic force microscopy (AFM) and microhardness measurements are applied in order to study the load and temperature driven changes in the phase composition and micro-structure of rail specimens at the surface and in the bulk ...
Y. Jirásková +4 more
openaire +1 more source
Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit, 2011
A validated three-dimensional (3D) transient finite element model is used to evaluate the wheel–rail impact at singular rail surface defects and the resulted high-frequency dynamic forces at the discrete supports of the rail. A typical ballasted railway track is modeled, in which the supports of the rail are composed of the fastenings, the sleepers ...
X Zhao, Z Li, J Liu
openaire +1 more source
A validated three-dimensional (3D) transient finite element model is used to evaluate the wheel–rail impact at singular rail surface defects and the resulted high-frequency dynamic forces at the discrete supports of the rail. A typical ballasted railway track is modeled, in which the supports of the rail are composed of the fastenings, the sleepers ...
X Zhao, Z Li, J Liu
openaire +1 more source
A Coarse-to-Fine Model for Rail Surface Defect Detection
IEEE Transactions on Instrumentation and Measurement, 2019Computer vision systems have attracted much attention in recent years for use in detecting surface defects on rails; however, accurate and efficient recognition of possible defects remains challenging due to the variations shown by defects and also noise. This paper proposes a coarse-to-fine model (CTFM) to identify defects at different scales.
Haomin Yu +6 more
openaire +2 more sources
Current distributions in the surfaces of railgun rails
Engineering Analysis, 1985Abstract This paper demonstrates the use of the Boundary Element Method (BEM) to study current and field distributions in railguns. The method is much simpler than earlier reported methods and is versatile in its applications. Good accuracy is obtained using few elements. Constant elements were used.
openaire +1 more source
Grinding induced martensite on the surface of rails [PDF]
Rolling contact fatigue (RCF) is causing crack initiation and crack propagation in rails. Some types of RCF cracks are found to be associated with a white etching layer (WEL). A metallurgical investigation was carried out on a worn rail and the amounts of WEL at different positions on the rail were determined.
Rasmussen, C.J. +3 more
openaire
Detection for Rail Surface Defects via Partitioned Edge Feature
IEEE Transactions on Intelligent Transportation Systems, 2022Jianwei Liu, Chao Wang, Ziji Ma
exaly

