Results 231 to 240 of about 38,509 (306)

Deterministic Detection of Single Ion Implantation

Advanced Engineering Materials, EarlyView.
Focused ion beam implantation with high detection efficiencies will enable the rapid and scalable fabrication of advanced spin‐based technologies such as qubits. This work presents the detection efficiencies of a wide range of ions implanted into solid‐state hosts, with efficiencies of >90% recorded for ion species and substrate combinations of ...
Mason Adshead, Lok Kan Wan, Maddison Coke, Janet Jacobs, Nicholas F. L. Collins, Mark C. Rosamond, Richard J. Curry   +6 more
wiley   +1 more source

Hybrid endomicroscopic objective with monolithic multi-material achromatic triplet fabricated using two-photon lithography. [PDF]

Appl Opt
Liu J, Lycke R, Luan L, Tkaczyk TS.
europepmc   +1 more source

Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices

Advanced Engineering Materials, EarlyView.
This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay, J. Schneider, P. Harrison, S. Kumar   +3 more
wiley   +1 more source

AI-enabled manufacturing process discovery. [PDF]

PNAS Nexus
Quispe D, Kozjek D, Mozaffar M, Xue T, Cao J.   +4 more
europepmc   +1 more source

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Novel sensorized additive manufacturing-based enlighted tooling concepts for aeronautical parts. [PDF]

Sci Rep
Uralde V, Veiga F, Suarez A, Lopez A, Goenaga I, Ballesteros T.   +5 more
europepmc   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Development of ranking alternatives of micro-cup production from directionally rolled copper rods using the Intuitionistic Fuzzy MARCOS method. [PDF]

Sci Rep
Sivam SPSS, Kesavan S, Ajiboye TK.
europepmc   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source