Reaction Sintering of Biocompatible Al2O3–hBN Ceramics [PDF]
ACS Omega, 2022 Biocompatible Al2O3–hBN ceramic was sintered from AlN and B2O3 precursors by reaction hot pressing at 1750 °C and 30 MPa for 8 min. The ceramic was compared to nonreactive (NR) one sintered from Al2O3 and BN under the same sintering conditions.
Oleksii Popov +4 more
doaj +3 more sources
The influence of Iron and Aluminium Powder Pressing on the Course of Shrinkage and Properties of the Fe40Al Phase Obtained by Reaction Sintering [PDF]
Archives of Metallurgy and Materials, 2022 The effect of the compaction rate on the structure, microstructure and properties of Fe-Al sinters obtained during the SHS reaction is presented in this paper. It was found that increasing the uniaxial pressing pressure led to the increase of the contact
M. Berendt-Marchel, D. Siemiaszko
doaj +1 more source
Thermal decomposition and reaction sintering for synthesis of mullite-zirconia composite using kaolin, γ-alumina and zirconia [PDF]
Cerâmica, 2021 The refractory materials used in the wall of the furnaces for glass melting can be prepared from mullite-zirconia composite material. The composite of mullite/zirconia was synthesized from Iraqi kaolin, γ-alumina, and zirconia using thermal decomposition
M. A. Aswad +2 more
doaj +2 more sources
Reaction sintering in compacted hydrolysed carbonated calcium phosphate [PDF]
Processing and Application of Ceramics, 2023 The thermal behaviour of the compact of an uncalcined hydrolysed carbonated calcium phosphate powder slowly heated in air (i.e. under conditions of the reaction sintering) was studied to reveal the reactions which could influence its densification up to ...
Zyman Zoltan +6 more
doaj +1 more source
Metals, 2020 Element reaction−diffusion of Ti/Al2O3 composite which was fabricated at various sintering temperatures, holding times, and a sintering pressure of 30 MPa has been discussed in the present research.
Guopu Shi, Liu Zhang, Zhi Wang
doaj +1 more source
In-situ formation and densification of MgAl2O4-Y3Al5O12 and MgAl2O4-MgNb2O6 ceramics via a single-stage SRS process [PDF]
Science of Sintering, 2017 MgAl2O4 (MA)-Y3Al5O12 (YAG) and MA-MgNb2O6 (MN) ceramics with high density were successfully fabricated via a single-stage solid-state reaction sintering (SRS) process at 1580°C for 4 h.
Zhang Bowen +6 more
doaj +1 more source
Reaction sintering of the 2ZnO-TiO2 system [PDF]
Science of Sintering, 2007 Sintering kinetics of the mechanically activated ZnO-TiO2 system was studied. Mixtures of ZnO and TiO2 powders were mechanically activated using a high-energy ball mill for different time intervals from 0 to 300 minutes.
Obradović N. +3 more
doaj +1 more source
Preparation of Al–Si alloy semi-solid billets by liquid phase reaction sintering
Fenmo yejin jishu, 2022 The Al–6%Si (mass fraction) semi-solid billets were prepared by liquid phase reaction sintering in this paper, using Al and Si elemental powders. In the results, the mixed Al–6%Si powders have the good cold pressing forming properties, and the relative ...
LIU Wen-chao +4 more
doaj +1 more source
Mo diffusion and In-situ formation of reinforcement in spark plasma sintering of powder mixed Ti-10Mo-1.5B4C composite at different temperatures and holding time [PDF]
مواد نوین, 2023 Introduction: Titanium boride and titanium carbide are the most important ceramic particles to reinforce titanium-molybdenum alloys. If an external reinforcement with an exothermic reaction causes the production of those reinforcements, the heat of ...
Marjan Ranjbari +2 more
doaj +1 more source
In-situ reactive synthesis of full dense Si2N2O by incorporating of Amourphous nanosized Si3N4;effect of MgO and Y2O3 [PDF]
Journal of Nanostructures, 2019 Si2N2O is considered as a new great potential structural/functional candidate in place of Si3N4. The amorphous Si3N4 nanopowder was incorporated into silica sol by adding of MgO and Y2O3 as sintering aid.
Mohammad Rezazadeh +3 more
doaj +1 more source