Results 61 to 70 of about 27,819 (290)

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

Advanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho, M. Naeem, T. H. C. Costa, M. S. Libório, J. C. A. Queiroz, C. B. B. Luna, R. R. M. Sousa, P. S. Vieira, E. M. Araújo   +8 more
wiley   +1 more source

Phase transformation and mechanical properties of B4C/Al composites

Journal of Materials Research and Technology, 2020
Lamellar constituted with 5, 15, 25 vol.% B4C/Al composites and homogeneous (namely 5, 15, 25 vol.% B4C/Al) composites were fabricated at sintering temperature 680 °C, sintering pressure 30 MPa, and heat preservation period 90 min via vacuum hot-pressing
Liu Zhang, Guopu Shi, Kun Xu, Wu Hao, Qinggang Li, Wu Junyan, Zhi Wang   +6 more
doaj   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Preparation and application of foamed ceramic panels in interior design

Science and Engineering of Composite Materials, 2023
A new type of foam ceramics was prepared with fly ash (CFA). Before sintering, the CFA underwent alkali activation, resulting in an even layer of hydroxy sodalite crystals covering the CFA particles. The pre-treatment of the CFA-alkali-activated material
Wang Bin
doaj   +1 more source

Consolidation of WC-Co nanocomposites synthesised by mechanical alloying [PDF]

, 2009
A thesis submitted in partial fulfilment of the requirements of the University of Wolverhampton for the degree of Doctor of PhilosophyThe influence of mechanical alloying (MA) milling time, temperature, sintering method and microstructure on the ...
Stephen A. Hewitt Beng, Hewitt, Stephen A.   +1 more
core  

Effects of dispersion surfactants on the properties of ceramic – carbon nanotube (CNT) nanocomposites [PDF]

, 2014
Gum Arabic (GA), Sodium Dodecyl Sulfate (SDS) and their mixture were used for the dispersion of multi-walled carbon nanotubes (CNTs) in an alumina matrix. A good dispersion at low loadings (0.5-1 wt%) of CNTs in alumina was achieved by an ultrasonic bath
Inam, Fawad, Brown, Peter, Heaton, Andrew, Reece, Michael, Peijs, Ton   +4 more
core   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Microwave Reaction Sintering of Tungsten Carbide Cobalt Hardmetals [PDF]

, 1996
Microwave reaction sintering of tungsten- carbon-, cobalt mixtures is described as a method that combines the liquid phase reaction sintering of tungsten carbide cobalt hardmetals with the enhanced densification behavior of hardmetals in the microwave ...
K. Rödiger, K. Dreyer, T. Gerdes, M. Willert-Porada   +3 more
core   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Deep desulfurization of sintering flue gas in iron and steel works based on low-temperature oxidation

Open Chemistry, 2020
The deep desulfurization method of sintering flue gas based on the low-temperature oxidation method is studied. Based on the analysis of the main principle of deep desulfurization of sintering flue gas, a deep desulfurization system of sintering flue gas
Meng Hua
doaj   +1 more source