Results 21 to 30 of about 23,732 (261)
Reactivation of shutdown reactor plants [PDF]
This report presents preliminary planning information which supplements two prior special reactor study reports. It is the purpose of this study to consider expedited reactivation of reactors and to evaluate the factors which are likely to be controlling to, or have a major influence on the time required to reactivate one or more of Hanford`s six small
openaire +2 more sources
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
After the first concrete was poured on December 9, 2012 at the Shidao Bay site in Rongcheng, Shandong Province, China, the construction of the reactor building for the world's first high-temperature gas-cooled reactor pebble-bed module (HTR-PM ...
Zuoyi Zhang +12 more
doaj +1 more source
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Design and Verification of Reactor Power Control Based on Stepped Dynamic Matrix Controller
As key equipment in nuclear power plant, the reactor power control system is adopted to strictly control and regulate the reactor power of a PWR (pressurized water reactor) in a nuclear power plant.
Xu Zhang +5 more
doaj +1 more source
In this research work, an advanced most modern ACP1000 Nuclear Power Plant is addressed. An enhanced fractional order model of ACP1000 nuclear power plant is adopted with an addition of protection and safety systems. The whole plant model is developed by
Arshad Habib Malik +3 more
doaj +1 more source
Modular Critical Element Recycling Platform Using a Nanoporous Additively Manufactured Gyroid
A modular recycling platform integrates 3D‐printed nanoporous gyroid structures to enable efficient critical element recovery. This system utilizes a hierarchical architecture, combining macroscopic channels with polymerization‐induced nanoscale porosity. By systematically tuning structural wall thickness and resin formulation, the platform achieves an
Xiangyu Gao +6 more
wiley +1 more source
Control Problems Associated with an Open Loop Unstable Chemical Reactor
A batch reaction is carried out in a water-cooled reactor on a small pilot scale plant. Control problems arose because of the inherent one loop instability of the reactor due to insufficient heat transfer area between the reactor contents and the cooling
C. While
doaj +1 more source
A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič +7 more
wiley +1 more source
Integration of Low‐Voltage Nanoscale MoS2 Memristors on CMOS Microchips
This article presents the first monolithic integration of nanoscale MoS2‐based memristors into the back‐end‐of‐line of foundry‐fabricated CMOS microchips in a one‐transistor‐one‐resistor (1T1R) architecture. The MoS2‐based 1T1R cells exhibit forming‐free, nonvolatile resistive switching with ultra‐low operating voltages, low cycle‐to‐cycle variability ...
Jimin Lee +16 more
wiley +1 more source

