Results 181 to 190 of about 427 (202)

Influence of synchronized rolling-assisted process on crack and properties of Ni-WC laser cladding layers. [PDF]

Sci Rep
Zhang H, Dai X, Guo H, Hu X, Shen W, Ma C, Zhao C.   +6 more
europepmc   +1 more source

Automated Intracellular Immunofluorescence Staining Enabled by Magnetic 3D Mixing in a Modular Microfluidic Platform. [PDF]

Biosensors (Basel)
Zhang Z, Wang M, Zhong R, Zhao Y, Sun Y.
europepmc   +1 more source

Microstructural and Performance Analysis of (TiAl)_95-xCu₅Ni_x Coatings Prepared via Laser Surface Cladding on Ti-6Al-4V Substrates. [PDF]

Materials (Basel)
Jia W, Song X, Zhu Y, Jiang D, Liu M, Ji Y, Zhou D, Wang Y.   +7 more
europepmc   +1 more source

Modified-Roll Profile Correction for a Gear Shaping Cutter Made by the Lengthwise-Reciprocating Grinding Process

Journal of Mechanical Design, Transactions of the ASME, 2011
The tooth profile error of a gear shaping cutter made by the lengthwise-reciprocating grinding process (LRGP) is usually corrected by modifying the grinding wheel profile. However, such grinding wheel modification cannot eliminate the twisting profile error along the face of the shaping cutter.
Zhang-Hua Fong, Fong Zhang-Hua
exaly   +3 more sources

The Influence of Crank Speed of Bush Reciprocating Cutter on Bush Cut

2010 International Conference on Digital Manufacturing & Automation, 2010
Bush is one of raw material for biomass fuel in China. Crank speed is an important parameter in the design of bush reciprocating cutter. A reciprocating single blade cutting test equipment was made in this paper. One factor test was done to study its influence on maximum cutting force of bush.
Chen Cheng, Yu Guosheng, Chen Zhongjia, Liu Xiaohu, Zhang Shaoquan   +4 more
exaly   +3 more sources

Design of a Reciprocating Manual Weed Cutter for Hill Orchard

Journal of Agricultural Engineering (India), 2014
Cutting of weeds in hill orchards is labour and time intensive. When performed with grass slasher or traditional dao through impact cutting, it consumes approximately 50% of total labour requirement for cultivation. A simple and low-cost reciprocating weed cutter was designed with a cutter bar width of 600 mm.
null S. Mandal, null Arvind Kumar, null R. K. Singh   +2 more
openaire   +2 more sources

Dynamic Analysis of Reciprocating Single-Blade Cutter Bars

Transactions of the ASABE, 2007
In this study, a mathematical lumped mass model for a reciprocating single-blade cutter bar with a slider-crank mechanism was developed. The equation of motion was numerically integrated, and the influence of geometric, kinematic, dynamic, and biological parameters was investigated.
GUARNIERI, ADRIANO, MAGLIONI, CESARE, MOLARI, GIOVANNI   +2 more
openaire   +3 more sources

Some of the next articles are maybe not open access.

Related searches:

Simulation Analysis of Reciprocating Cutter Based on ADAMS

Advanced Materials Research, 2013
We developed reciprocating cutter, then use software ADAMS to optimize and improve it. The output of simulation shows that the cutter performance is good, while vibration problem exists at the same time.
Xiang Chun Wang, Nan Cai, Weng Zhang
exaly   +2 more sources

Design and Kinematic Analysis of Reciprocating Cutters

Applied Mechanics and Materials, 2013
[Purpos] in order to solve design problems of the cutter for the seedling vegetable harvester, a reciprocating cutter with a crank linkage mechanism has been designed. [Metho SolidWorks software has been adopted for virtual design of parts and assemblies of the reciprocating cutter for the seedling vegetable harvester.
Zhi Qiang Li, Li Zhi Qiang
exaly   +2 more sources

Profile correction of a helical gear shaping cutter using the lengthwise-reciprocating grinding method

Mechanism and Machine Theory, 2009
Currently, the Isoform® lengthwise-reciprocating grinding process is considered the most accurate method for generating the tooth profile of a gear shaping cutter. However, despite improving the profile accuracy of the grinding shaper, the Isoform® ground helical shaping cutter, especially one with a small tooth number, still produces pressure angle ...
Zhang-Hua Fong
exaly   +2 more sources