Results 41 to 50 of about 34,576 (259)

Location Privacy in Spatial Crowdsourcing

open access: yes, 2017
Spatial crowdsourcing (SC) is a new platform that engages individuals in collecting and analyzing environmental, social and other spatiotemporal information.
A Liu   +9 more
core   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

open access: yesAdvanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin   +2 more
wiley   +1 more source

Multidimensional Zero-Correlation Linear Cryptanalysis of the Block Cipher KASUMI [PDF]

open access: yes, 2014
The block cipher KASUMI is widely used for security in many synchronous wireless standards. It was proposed by ETSI SAGE for usage in 3GPP (3rd Generation Partnership Project) ciphering algorthms in 2001.
Chen, Shaozhen, Yi, Wentan
core  

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

open access: yesAdvanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann   +6 more
wiley   +1 more source

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

open access: yesAdvanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi   +7 more
wiley   +1 more source

Dynamic model and control of a new quadrotor unmanned aerial vehicle with tilt-wing mechanism [PDF]

open access: yes, 2008
In this work a dynamic model of a new quadrotor aerial vehicle that is equipped with a tilt-wing mechanism is presented. The vehicle has the capabilities of vertical take-off/landing (VTOL) like a helicopter and flying horizontal like an airplane ...
Aksit, Mahmut Faruk   +11 more
core  

Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy

open access: yesAdvanced Engineering Materials, EarlyView.
This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb   +6 more
wiley   +1 more source

A performance analysis of Generalized Key Scheme Block Cipher (GKSBC) algorithm to Cryptanalytic Attacks [PDF]

open access: yes, 2016
Information is a commodity. Information has economic value and production of it incurs cost. Securing the information is posing a considerable challenge.
Jothi, S. A. (S)
core  

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

open access: yesAdvanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han   +5 more
wiley   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

open access: yesAdvanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter   +9 more
wiley   +1 more source

Home - About - Disclaimer - Privacy