Results 141 to 150 of about 14,661,551 (240)

Development Status of Fe-V-Based High-Entropy Alloys for Nuclear Reactors. [PDF]

Materials (Basel)
Wu H, Fu Y, Liu P, Wang T, Han W, Yi X, Zhan Q, Wan F.   +7 more
europepmc   +1 more source

A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation

Advanced Engineering Materials, EarlyView.
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler, Nikolaus Kostwein, Ronald Schnitzer, Christian Mitterer, Verena Maier‐Kiener   +4 more
wiley   +1 more source

Single-Stage PET Waste Upcycling into Copolymers: Study of Thermal Properties and Crystallization. [PDF]

Polymers (Basel)
Kirshanov KA, Aliev GS, Ismaylov DA, Lobanova NA, Pogorely AM, Toms RV, Gervald AY.   +6 more
europepmc   +1 more source

Effects of Mg on Microstructure and Solidification of a Hypereutectic Zn–8 wt.%Al Alloy

Advanced Engineering Materials, EarlyView.
An appreciable set of results involving thermal data, microstructure, chemical composition, and microstructural growth laws is reported for ZnAlMg alloys. Such results demonstrate that ZnAlMg alloys have high potential for applications in automotive self‐lubricating components, batteries, and electrical systems.
Raí B. de Sousa, Jeverton L. Paixão, Daylla S. Silva, Bruno S. Sobral, Mucio D. de Medeiros, José E. Spinelli, Bismarck L. Silva   +6 more
wiley   +1 more source

Phase Transformations During Softening of Iron Ore Sinter of Varying Basicity in the CaO-SiO₂-FeO System. [PDF]

Materials (Basel)
Vyaznikova EA, Dmitriev AN, Vitkina GY, Katayev VV.   +3 more
europepmc   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Physical Simulation of Phase Separation at the Slag-Metal Interface During Pellet Melting: A Phenomenological Study. [PDF]

Materials (Basel)
Wang Y, Du Z, Song G, Chen L, Dang J, Chen C.   +5 more
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Surface Integrity and Mechanical Performance of Vertically Printed FDM-PLA After Laser Polishing: Coupled Effects of Scan Orientation and Hatch Distance. [PDF]

Polymers (Basel)
Stolárik G, Vandžura R, Radchenko S, Hlaváček P, Geľatko M.   +4 more
europepmc   +1 more source