Results 201 to 210 of about 865,993 (309)

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Deep coverage and extended sequence reads obtained with a single archaeal protease expedite de novo protein sequencing by mass spectrometry.

Cell Syst
Pérez Pañeda L, Kadavá T, Shamorkina TM, Schulte D, Pribil P, Heidelberger S, Narlock-Brand AM, Yannone SM, Snijder J, Heck AJR.   +9 more
europepmc   +1 more source

Retraction notice to "Non-tuberculous mycobacterial infections among patients with suspected or confirmed pulmonary tuberculosis in Ethiopia: A systematic review and meta-analysis" [IJID Reg 16 (2025) 100692]. [PDF]

IJID Reg
Daka D, Tessema B, Mutshembele A, Alelign A, Birhan W, Gelaw B.   +5 more
europepmc   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Accelerated Feature Selection via Discernibility Hashing: A Rough Set Approach. [PDF]

Entropy (Basel)
Luo S, Shi L, Chen L, Cao X.
europepmc   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source

Perspectives on Robustness and Resilience of Complex Networks. [PDF]

Entropy (Basel)
Proverbio D, Boccaletti S.
europepmc   +1 more source

Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones

Advanced Engineering Materials, EarlyView.
A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell, Martha Leach, Hongtao Song, Carolyn Seepersad   +3 more
wiley   +1 more source

GUI test case minimization using sequence mining. [PDF]

PLoS One
Ambreen R, Khan TA.
europepmc   +1 more source