Results 211 to 220 of about 2,382 (289)

A quantum crystallographic protocol for general use. [PDF]

Sci Rep
Balmohammadi Y, Malaspina LA, Nakamura Y, Cametti G, Siczek M, Grabowsky S.   +5 more
europepmc   +1 more source

Refining the prognostic role of red cell distribution width in TAVR patients

Artur Dziewierz
openalex   +2 more sources

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Multipolar model and Hirshfeld atom refinement of tetraaquabis(hydrogenmaleato)iron(II). [PDF]

Acta Crystallogr B Struct Sci Cryst Eng Mater
Ferreira Guimarães H, Lages Rodrigues B.   +1 more
europepmc   +1 more source

Refining Uniform Discrimination Metrics: Towards a Case‐by‐Case Weighting Evaluation in Species Distribution Models With Presence‐Absence Data [PDF]

Alberto Jiménez‐Valverde
openalex   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Benchmarking 3D-ΔPDF analysis using in-house X-ray sources. [PDF]

Acta Crystallogr A Found Adv
Juul KOR, Støckler KAH, Iversen BB.
europepmc   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Powder diffraction data beyond the pattern: a practical review. [PDF]

J Appl Crystallogr
Casati N, Boldyreva E.
europepmc   +1 more source

Experimental Study of Silicon Refining by Slag Treatment: Distribution of Boron and Phosphorus [PDF]

Katri Avarmaa, Andreas Diga Pratama Putera, Chen Jiang, Geoffrey Brooks, Michael Somerville, M. Akbar Rhamdhani   +5 more
openalex   +1 more source