Results 61 to 70 of about 75,511 (297)

Virtual parameter calibration of pod pepper seeds based on discrete element simulation

open access: yesHeliyon
In order to achieve numerical optimization of the pod pepper seed sowing device, the contact parameters of pod pepper seeds were calibrated, with the angle of repose used as the response value.
Xingye Chen   +6 more
doaj   +1 more source

A two-species continuum model for aeolian sand ripples [PDF]

open access: yes, 1999
We formulate a continuum model for aeolian sand ripples consisting of two species of grains: a lower layer of relatively immobile clusters, with an upper layer of highly mobile grains moving on top.
A. Mehta   +29 more
core   +2 more sources

Angle of repose

open access: yesThe American Journal of Emergency Medicine
Citation: 'angle of repose' in the IUPAC Compendium of Chemical Terminology, 5th ed.; International Union of Pure and Applied Chemistry; 2025. Online version 5.0.0, 2025. 10.1351/goldbook.15152 • License: The IUPAC Gold Book is licensed under Creative Commons Attribution-ShareAlike CC BY-SA 4.0 International for individual terms.
openaire   +3 more sources

Piezoresistive Monitoring of Carbon Nanomaterial‐Reinforced Epoxy Composites Under Cyclic and Fatigue Loading: A Review

open access: yesAdvanced Engineering Materials, EarlyView.
Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente   +3 more
wiley   +1 more source

Vortex microavalanches in superconducting Pb thin films

open access: yes, 2003
Local magnetization measurements on 100 nm type-II superconducting Pb thin films show that flux penetration changes qualitatively with temperature. Small flux jumps at the lowest temperatures gradually increase in size, then disappear near T = 0.7Tc ...
A. M Campbell   +22 more
core   +1 more source

3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs

open access: yesAdvanced Engineering Materials, EarlyView.
This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu   +4 more
wiley   +1 more source

Calibration and test of contact parameters for alfalfa stalk at primary florescence based on discrete element method.

open access: yesPLoS ONE
In view of the lack of accurate models for discrete element simulation in the current research and development process of forage harvesting and crushing machinery, the contact parameters were calibrated based on Hertz-Mindlin (no slip) contact model by ...
Tao Chen   +4 more
doaj   +1 more source

Investigation of Oxygen‐Free Wetting Behavior of Aluminum on Copper via Molecular Dynamics Simulations and Experiments

open access: yesAdvanced Engineering Materials, EarlyView.
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu   +8 more
wiley   +1 more source

Angle of repose of granulated ice: effect of wood ash

open access: yesJournal of Glaciology
New experiments have revealed that the addition of a small amount of wood ash doubles the angle of repose of granulated ice at −10°C, but has little effect at −30°C. It is hypothesized that this behavior may be explained in terms of the freezing of water
William M. Harris   +2 more
doaj   +1 more source

Effect of clay content on the shear strength of clay–sand mixture

open access: yesInternational Journal of Geo-Engineering, 2018
This paper investigates the effect of clay content on the shear strength of clay–sand mixtures. Bentonite and Jumunjin sand were mixed to prepare clay–sand mixtures with varying clay contents of 5, 10, 15, 20, 25 and 30%.
Donghwi Kim, Boo Hyun Nam, Heejung Youn
doaj   +1 more source

Home - About - Disclaimer - Privacy