Results 121 to 130 of about 1,433,790 (312)
Modular Critical Element Recycling Platform Using a Nanoporous Additively Manufactured Gyroid
Advanced Engineering Materials, EarlyView.A modular recycling platform integrates 3D‐printed nanoporous gyroid structures to enable efficient critical element recovery. This system utilizes a hierarchical architecture, combining macroscopic channels with polymerization‐induced nanoscale porosity. By systematically tuning structural wall thickness and resin formulation, the platform achieves an
Xiangyu Gao +6 more
wiley +1 more source
Gas combustion retorting detailed run summary sheet retort no. 3 runs C1027-4 start-up [PDF]
, 2022 Reports of the Retort No. 3 runs were sent monthly to the Technical Advisory Committee members: Sinclair Research, Inc., Sinclair Oil and Gas Company, Mobil Oil Corporation, Pan American Petroleum Corporation, Esso Research and Engineering Company ...
core
The residual oil distribution regularity of low permeability oilfield
Petroleum, 2015 Study on the residual oil distribution regularity is the important thing during the middle and later stage of the oilfield. With understanding and development of oilfield, the research methods of remaining oil are varied.
Huan Zhao, Hongjun Yin
doaj +1 more source
Multilayer Self‐Limiting Electrospray Deposition via Stepped Voltage Bias
Advanced Engineering Materials, EarlyView.Self‐limiting electrospray deposition (SLED) uses a high voltage to generate and deposit a charged payload on a target surface. The coating retains its charge, repelling newly arriving material. SLED thickness can be decreased by applying a secondary bias to the target.
Madhuri Deb +3 more
wiley +1 more source
Laborary analysis sheet retort no. 3 runs C1023 start-up [PDF]
, 2022 Reports of the Retort No. 3 runs were sent monthly to the Technical Advisory Committee members: Sinclair Research, Inc., Sinclair Oil and Gas Company, Mobil Oil Corporation, Pan American Petroleum Corporation, Esso Research and Engineering Company ...
core
Experimental investigation of laminar and turbulent displacement of residual oil film. [PDF]
Sci Rep, 2023 Zhang Y, Barrouillet B, Skadsem HJ.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Residual adhesive after electrode loading in adhesive‐assisted resistance spot welding is quantified through a traceable experimental‐to‐digital workflow. Chromatic confocal topography provides calibrated surface‐height data, while OpenCV detects the electrode imprint and integrates adhesive height into comparable volume metrics.
Sung‐Min Wi, Jiangdong Zhao
wiley +1 more source
Laboratory analysis sheet retort no. 3 runs C-1026 start-up [PDF]
, 2022 Reports of the Retort No. 3 runs were sent monthly to the Technical Advisory Committee members.The United States Bureau of Mines facility at Anvil Points, near Rifle, Colorado, was reactivated starting in May 1964 and was operated during 1965, 1966, and ...
core
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Evaluation of Hydrocarbon Saturation Using Carbon Oxygen (CO) Ratio and Sigma Tool
Iraqi Journal of Chemical and Petroleum Engineering, 2014 The main aim of this study is to evaluate the remaining oil in previously produced zones, locate the water productive zone and look for any bypassed oil behind casing in not previously perforated intervals.
Usama S. Alameedy
doaj