Results 111 to 120 of about 77,791 (311)
Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio
This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov +4 more
wiley +1 more source
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi +7 more
wiley +1 more source
Phytoxicity study of the products of wet oxidation of a representative biomass (lettuce) [PDF]
In an attempt to verify the results reported previously concerning the phytotoxicity of wet-oxidation (wet-ox) products, lettuce solids were suspended in water and then heated to 548 K for 3.6 ksec (1 hr) under 4.1x10 to the -7 Pa (400 psig at 294 K ...
Onisko, B. L., Wydeven, T.
core +1 more source
Silver-based Microbial Check Valve for Spacecraft Potable Water Systems [PDF]
As human space exploration increases, the development of a more efficient potable water treatment system suited for spacecraft becomes crucial. This Waste-management Education Research Consortium (WERC) challenge was designed to explore the viability of ...
Garcia, Rogelio E
core +2 more sources
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
3D Printed Soft Robotic Hand [PDF]
Soft robotics is an emerging industry, largely dominated by companies which hand mold their actuators. Our team set out to design an entirely 3D printed soft robotic hand, powered by a pneumatic control system which will prove both the capabilities of ...
Kisner, Zack +2 more
core +1 more source
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
Testing Intra-Industry Trade Between Portugal and Spain [1990-1996] [PDF]
This paper shows how, in the period 1990-1996, economic integration between the two Iberian economies has deepened through intra-industry trade. The enquiry was led at the level of the main forty traded products.
Horácio C. Faustino +2 more
core
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
X-ray based tree ring analyses [PDF]
In this thesis, two x-ray based dendro-analyses (batch-wise microdensitometry and energy dispersive x-ray fluorescence (EDXRF)) and the conditions under which these methods could be used on the two typical boreal conifers Norway spruce (Picea abies (L ...
Lindeberg, Johan
core

