Results 181 to 190 of about 77,222 (268)

4D-Printed Temperature-Switchable Monolithic Packing for NIR-Actuated Elemental Speciation Analysis. [PDF]

Anal Chem
Chen YT, Ho YC, Su CK.
europepmc   +1 more source

Aerosol Jet Printing of Benzocyclobutene as a Thermally Stable, Low‐Loss Dielectric for Multilayer Microwave Electronics

Advanced Materials Technologies, EarlyView.
Multilayer aerosol jet printed components with a low‐loss, thermally stable dielectric are demonstrated using benzocyclobutene. Ink formulation and in‐line droplet evaporation control support high‐quality, versatile, and stable printing performance. A specialized measurement for low‐loss materials reveals promising microwave properties, which, combined
Md Ramjan Ali, Trent Moritz, Mohammad Tayeb Al Qaseer, Ethan B. Secor   +3 more
wiley   +1 more source

Effect of silane treatment and resin cement type on bond strength to three-dimensional printed restorative resin: an in vitro experimental study. [PDF]

Restor Dent Endod
Park SJ, Lee EH, Kim RJY, Shin JH.
europepmc   +1 more source

In Situ Formation of Ni‐P‐O‐C Interfaces in DLP‐Printed Carbon Microlattices for Efficient Alkaline Hydrogen Evolution

Advanced Materials Technologies, EarlyView.
Graphical abstract illustrating the fabrication of Ni–P–O–C porous carbon microlattice electrodes by DLP printing of Ni/P precursor‐containing resin followed by high‐temperature carbonization. The resulting conductive microlattice acts directly as the HER cathode in alkaline electrolyte, where in situ formed Ni–P–O–C interfaces provide active sites for
Muzahir Ali, Seongmin Lee, Tasadduq Hussain, Young Kyu Kim, Md. Ali Asgar, Jung Bin In, Seok‐min Kim   +6 more
wiley   +1 more source

Per-Layer UV Exposure-Dependent Cytotoxicity of 3D-Printed Aligner Resins and Estrogen-like Activity Screening. [PDF]

Polymers (Basel)
Šimunović L, Marić AJ, Meštrović S.
europepmc   +1 more source

In‐House Manufacturing of 3D ECM Culture Chips via Vacuum Thermoforming for Enhanced Imaging Applications

Advanced Materials Technologies, EarlyView.
Desktop vacuum thermoforming enables rapid, low‐cost fabrication of 96‐channel polystyrene culture chips with very thin imaging interfaces. The resulting platform supports cell lines, primary cells, and patient‐derived organoids, and enables high‐resolution confocal microscopy and single‐cell visualization, providing an accessible approach for advanced
Aleksandra Fomina, Adam Tam, Jennifer Lam, Nila C. Wu, Nancy T. Li, Alison P. McGuigan   +5 more
wiley   +1 more source

Rapid thermoforming of polycarbonate cell culture accessories from 3D printed molds. [PDF]

PLoS One
Malayath G, Wang F, Zhou C, Huebsch N.
europepmc   +1 more source

Liquid Crystal Elastomer Actuator Matrix for Large Area Applications

Advanced Materials Technologies, EarlyView.
A scalable approach is used to manufacture a digitally‐controllable, 2D 5 × 5 actuator matrix. The elements of the matrix are produced by direct ink writing of a liquid crystal elastomer ‘artificial muscle’ on large‐area flexible thin‐film heaters. In optimizing the low‐power actuators, multiple heater designs and substrate materials are investigated ...
Giulia Spallanzani, Bart Peeters, Danqing Liu, Peter Zalar, Hylke B. Akkerman, Jeroen A. H. P. Sol   +5 more
wiley   +1 more source

Preparation and evaluation of high-performance modified poly(ester-amide), and study its biological activity after its formulated as a vehicle for protective coating. [PDF]

Sci Rep
El-Wahab HA, Fayad MM, Hendy MH, Salem SS, Mahmoud AM.   +4 more
europepmc   +1 more source