Results 211 to 220 of about 36,677 (301)

Computer Modeling of the Ferrite‐To‐Austenite Transformation in a Super‐Duplex Stainless Steel and the Important Role of Trans‐Interface Diffusion

steel research international, EarlyView.
An accurate moving boundary model for volume diffusion containing boundary conditions from trans‐interface diffusion (TID) simulates the austenite growth during cooling. TID of Cr, Mo, N and Ni enhance growth kinetics. Without TID, compositions of the interface region change, decreasing the driving force for growth and finally causing numerical ...
A. Salwén, T. Müller, S. Nouhi, J. Y. Jonsson   +3 more
wiley   +1 more source

Prediction of tensile strength in aluminum spot welding using machine learning. [PDF]

Sci Rep
Seo BW, Son HJ, Han SB, Jo IS, Kim CJ, Cho YT.   +5 more
europepmc   +1 more source

Crash Behavior of DP800–DP1000 Advanced High‐Strength Steel’s Dissimilar Resistance Spot Welded Joints Under Quasi‐static and High Strain Rates

steel research international, EarlyView.
The high‐strain‐rate behavior of resistance spot‐welded DP800–DP1000 joints is investigated. Results show that microstructural gradients across BM–HAZ–FZ govern hardness, strain rate sensitivity, and failure modes. While strength increases with strain rate, energy absorption is controlled by ductility, with DP800–DP800 joints showing superior ...
Pankaj Shrivastava, Velaphi Msomi
wiley   +1 more source

Tab-to-Busbar Interconnections in EV Battery Packs: An Introductory Review of Typical Welding Methods. [PDF]

Micromachines (Basel)
Choi S, Lim S, Shan A, Lee J, Yun TG, Hwang B.   +5 more
europepmc   +1 more source

Performance analysis of strengthening reinforced concrete beams under pure torsion using galvanized steel sheets: Experimental and numerical investigation

Structural Concrete, EarlyView.
Abstract Reinforced concrete (RC) beams can be subjected to torsion, and failure due to torsion is brittle and poses a significant risk to occupants. Moreover, strengthening of existing RC beams in torsion may be required due to the upgrade of the structures or as part of structural rehabilitation.
Ahmed Hamoda, Mizan Ahmed, Ahmad G. Saad, Aref A. Abadel, Saad A. Yehia   +4 more
wiley   +1 more source

Optimization design and experimental verification of magnetic pulse spot welding system of dissimilar metal sheets based on a field shaper. [PDF]

Sci Rep
Zhang H, Li X, Ding H.
europepmc   +1 more source

Experimental and theoretical investigation of longitudinal tunnel lining joints with confining reinforcement

Structural Concrete, EarlyView.
Abstract Precast reinforced concrete segmental linings are frequently used in modern tunneling. In these linings, the longitudinal joints typically have a reduced contact cross‐section and thus often govern the design, particularly in tunnels under high hydrostatic pressure or crossing squeezing or swelling ground with correspondingly high ...
Fabian Morger, Albin Kenel, Walter Kaufmann   +2 more
wiley   +1 more source

High power diode laser beam welding of AA8011 aluminum alloy for enhanced mechanical performance in lightweight structures. [PDF]

Sci Rep
Patil R, Löfstrand M.
europepmc   +1 more source

Moment‐curvature behavior of continuous reinforced concrete slab strips—Experimental determination and modeling

Structural Concrete, EarlyView.
Abstract With the market introduction of new reinforcing materials, such as corrosion‐resistant steel, the effect of their stress–strain relationship on the ductility of reinforced concrete structures needs to be evaluated. Their moment‐curvature behavior significantly influences bending moment redistributions, rotation capacity, and deformation at ...
Nathalie Reckinger, Karel Thoma, Walter Kaufmann   +2 more
wiley   +1 more source

Features of the Structural Design of Welded Joints of Superelastic Nitinol Wires. [PDF]

Materials (Basel)
Kvasnytskyi V, Zvorykina A, Zvorykin L, Zvorykin C, Chvertko Y.   +4 more
europepmc   +1 more source