Results 231 to 240 of about 21,176 (299)

Computer Modeling of the Ferrite‐To‐Austenite Transformation in a Super‐Duplex Stainless Steel and the Important Role of Trans‐Interface Diffusion

steel research international, EarlyView.
An accurate moving boundary model for volume diffusion containing boundary conditions from trans‐interface diffusion (TID) simulates the austenite growth during cooling. TID of Cr, Mo, N and Ni enhance growth kinetics. Without TID, compositions of the interface region change, decreasing the driving force for growth and finally causing numerical ...
A. Salwén, T. Müller, S. Nouhi, J. Y. Jonsson   +3 more
wiley   +1 more source

Crash Behavior of DP800–DP1000 Advanced High‐Strength Steel’s Dissimilar Resistance Spot Welded Joints Under Quasi‐static and High Strain Rates

steel research international, EarlyView.
The high‐strain‐rate behavior of resistance spot‐welded DP800–DP1000 joints is investigated. Results show that microstructural gradients across BM–HAZ–FZ govern hardness, strain rate sensitivity, and failure modes. While strength increases with strain rate, energy absorption is controlled by ductility, with DP800–DP800 joints showing superior ...
Pankaj Shrivastava, Velaphi Msomi
wiley   +1 more source

Microstructure, Mechanical Properties and Additive Manufacturing of Steels. [PDF]

Materials (Basel)
Bidulský R, Bidulská J.
europepmc   +1 more source

Tailored Hardening and Isothermal Bainitizing of Additively Manufactured Nitrogen‐Enhanced Martensitic Chromium Steel

steel research international, EarlyView.
Tailored heat treatments transform additively manufactured high‐nitrogen martensitic Cr steel from austenitic as‐built condition to high‐hardness states. Isothermal bainitizing at 250°C generates an ultrafine nanostructure and achieves higher hardness than conventional hardening and tempering, highlighting a promising postprocessing route for laser ...
Philip König, Sebastian Weber, Jonathan Lentz   +2 more
wiley   +1 more source

Impact of Substrate Preheating on Weld Quality, Microstructure, Corrosion Resistance, and Mechanical Properties in Gas Tungsten Arc Welding of UNS S32750 Super Duplex Stainless Steel. [PDF]

Materials (Basel)
da Cruz Junior EJ, Ribeiro RH, Varasquim FMFA, Carvalho FO, Santiago LFF, Lemos GP, Ventrella VA, Calliari I.   +7 more
europepmc   +1 more source

Performance analysis of strengthening reinforced concrete beams under pure torsion using galvanized steel sheets: Experimental and numerical investigation

Structural Concrete, EarlyView.
Abstract Reinforced concrete (RC) beams can be subjected to torsion, and failure due to torsion is brittle and poses a significant risk to occupants. Moreover, strengthening of existing RC beams in torsion may be required due to the upgrade of the structures or as part of structural rehabilitation.
Ahmed Hamoda, Mizan Ahmed, Ahmad G. Saad, Aref A. Abadel, Saad A. Yehia   +4 more
wiley   +1 more source

Mechanical performance and microstructural behavior of ultrasonically welded PVC-coated polyester fabric seams at subzero temperature. [PDF]

Sci Rep
Eskandarnia G, Hejazi SM, Soltani P, Mashayekhi M.   +3 more
europepmc   +1 more source

Experimental and theoretical investigation of longitudinal tunnel lining joints with confining reinforcement

Structural Concrete, EarlyView.
Abstract Precast reinforced concrete segmental linings are frequently used in modern tunneling. In these linings, the longitudinal joints typically have a reduced contact cross‐section and thus often govern the design, particularly in tunnels under high hydrostatic pressure or crossing squeezing or swelling ground with correspondingly high ...
Fabian Morger, Albin Kenel, Walter Kaufmann   +2 more
wiley   +1 more source

Atomistic insight into Al-Mg friction stir welding process via molecular dynamics simulation. [PDF]

PLoS One
Nguyen VT, Hoang VH, Nguyen TT, Thien TN, Vo XT, Nguyen VTT.   +5 more
europepmc   +1 more source

Moment‐curvature behavior of continuous reinforced concrete slab strips—Experimental determination and modeling

Structural Concrete, EarlyView.
Abstract With the market introduction of new reinforcing materials, such as corrosion‐resistant steel, the effect of their stress–strain relationship on the ductility of reinforced concrete structures needs to be evaluated. Their moment‐curvature behavior significantly influences bending moment redistributions, rotation capacity, and deformation at ...
Nathalie Reckinger, Karel Thoma, Walter Kaufmann   +2 more
wiley   +1 more source