Results 71 to 80 of about 8,023,762 (316)

Distinct Microstructural Characteristic Lengths Defining Notch Fatigue Crack Initiation and Propagation, and Defect Tolerance in Advanced Steels

Advanced Engineering Materials, EarlyView.
Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Experimental study on long-distance shear characteristics of fully weathered granite residual soil

Zhongguo dizhi zaihai yu fangzhi xuebao
In recent years, with the intensification of global climate change and human engineering activities, mass landslide events triggered by rainfall have become frequent in southeast China, posing serious threats to the lives and property safety of the ...
Wuwei MAO, Long PAN, Chenrui FENG, Xu MOU, Yinbing CUI, Zhen GUO, Yu HUANG   +6 more
doaj   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Rate-Dependent Residual Strength of Unsaturated Slip-Zone Soil Under Suction-Controlled Conditions

Geosciences
Reservoir landslides undergo saturated–unsaturated transitions under hydrological variations. Matric suction significantly influences slip-zone soil strength.
Jin Yuan, Rui Zhu, Yanpian Mao, Lanlan Xu, Jianfan Zhao, Chao Zhang, Shu Zhang   +6 more
doaj   +1 more source

Supplementary Material for Shear et al.

Supplemental material for the manuscript, "Comparative Safety and Benefit-Risk Profile of Biologics and Oral Treatments for Moderate-to-Severe Plaque Psoriasis: a Network Meta-Analysis of Clinical Trial Data," by Shear et ...
Shear, N
core   +1 more source

Discrepancies Between Micro Versus Macroscale Viscoelastic Properties in a Microplastic‐Tissue Composite Model

Advanced Engineering Materials, EarlyView.
This study explores the discrepancies between bulk mechanics and spatial mapping in a tissue‐mimetic hydrogel model. Microplastic particles create localized stiff mechanical microenvironments that are detectable by cellular‐scale nanoindentation but leave bulk properties unchanged as measured by rheology.
Ahron T. Verschleisser, Baptiste Le Roi, Omri Leshem, Joshua M. Grolman   +3 more
wiley   +1 more source

Test

Tes
Test
core   +2 more sources

Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy

Advanced Engineering Materials, EarlyView.
Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang, Jianxiang Zhao, Zhaoqi Chen, Hao Gong, Yinsen Yan, Junlei Tao, Yong Yang   +6 more
wiley   +1 more source

Simulation‐Based Analysis of Insert Pull‐Out in Nickel‐Polyurethane Hybrid Foams Using CT‐Derived Geometries

Advanced Engineering Materials, EarlyView.
CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz, Jonas Fell, Hendrik Jost, Stefan Diebels, Hans‐Georg Herrmann   +4 more
wiley   +1 more source