Results 161 to 170 of about 15,419,997 (324)

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source

Dynamic Testing of Cold Gas Sprayed Bipolar Plates–Porous Transport Layer Coating System in Proton Exchange Membrane Water Electrolysis

Advanced Engineering Materials, EarlyView.
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin, Marvin Erck, Kevin Jasutyn, Katja Radermacher, Andreas Bund, Mario Kurniawan   +5 more
wiley   +1 more source

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

Advanced Engineering Materials, EarlyView.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk, Farhan Hossain, Felipe A. Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source

The Ripple Effect

, 2023
M. J. Barbosa
semanticscholar   +1 more source

Toward Low‐Consumable Anodes: Process Simulation and Prospective Life Cycle Assessment of NiFe2O4‐NiO‐Ni‐Cu vs. Prebaked Anodes for Aluminum Production with use of Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
Low‐consumable nickel ferrite‐based anodes for the Hall–Héroult process are compared with conventional prebaked carbon anodes using thermodynamic simulation and prospective life cycle assessment under contrasting future electricity system pathways from 2025 to 2050.
Felipe Alejandro Garcia Paz, Ulziikhuu Otgonbayar, Alexander Adamczyk, Farhan Hossain, Daniel Vogt, Johan Berg Pettersen, Alexandros Charitos   +6 more
wiley   +1 more source

Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories

Advanced Engineering Materials, EarlyView.
Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov, Eldar Salpagarov, Anhelina Mospan, Till Manon Jannis Stadtmüller, Thomas Schemmel, Christos Georgios Aneziris, Olena Volkova   +6 more
wiley   +1 more source

The ripple effect of stigmatization on children with congenital hypospadias: impacts on psychological and behavioral aspects. [PDF]

Front Public Health
Zhang W, Mo L, Liu T.
europepmc   +1 more source

Typhoon eye effect versus ripple effect: the role of family size on mental health during the COVID-19 pandemic in Pakistan. [PDF]

Global Health, 2021
Lateef T, Chen J, Tahir M, Lateef TA, Chen BZ, Li J, Zhang SX.   +6 more
europepmc   +1 more source