Casting Process at Roll Bite in Strip Cast Using Vertical-Type High-Speed Twin-Roll Caster
Metals, 2022 The solidification process in strip casting using a vertical-type high-speed twin-roll caster was clarified by inserting a 0.1 mm diameter K-type thermocouple into a strip during casting.
Toshio Haga
exaly +4 more sources
Ultrasonic roll bite measurements in cold rolling: Contact length and strip thickness [PDF]
Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 2017 In cold rolling of thin metal strip, contact conditions between the work rolls and the strip are of great importance: roll deformations and their effect on strip thickness variation may lead to strip flatness defects and thickness inhomogeneity.
Boman, R. +6 more
core +4 more sources
Ultrasonic roll bite measurements in cold rolling – Roll stress and deformation [PDF]
Journal of Materials Processing Technology, 2017 In cold rolling of thin metal strip, contact conditions between the work rolls and the strip are of great importance: roll deformations and their effect on strip thickness variation may lead to strip flatness defects and thickness inhomogeneity. To control the process, several online measurements are usually carried out such as the rolling load ...
Romain Boman, J -P Ponthot, N Legrand
exaly +4 more sources
Non-intrusive measurement of strip thickness and roll-bite length in metal rolling [PDF]
Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2020 It is important to monitor the rolled strip thickness standard to minimize material waste and loss of profit due to strip flatness defects, and also to maintain the product’s size and dimensional homogeneity. Several online measurement techniques are available but none of this can give an in situ measurement within the roll bite.
C Pinna, A Adebayo
exaly +4 more sources
Characterization of Roll Bite Heat Transfers in Hot Steel Strip Rolling and their Influence on Roll Thermal Fatigue Degradation [PDF]
Key Engineering Materials, 2013 A temperature sensor with a thermocouple placed at ~0.5 mm from roll surface is used in hot rolling conditions to evaluate by inverse calculation heat transfers in the roll bite. Simulation analysis in industrial hot rolling conditions with short contact lengths (e.g.
Nicolas Legrand +2 more
exaly +3 more sources
Analysis of Roll Gap Heat Transfers in Hot Steel Strip Rolling through Roll Temperature Sensors and Heat Transfer Models [PDF]
Key Engineering Materials, 2012 International audienceThis paper presents an analysis of roll bite heat transfers during pilot hot steel strip rolling. Two types of temperature sensors (drilled and slot sensors) implemented near roll surface are used with heat transfer models to ...
Nicolas Legrand +2 more
exaly +6 more sources
A Roll-Bite Profile Map Approach for the Prediction of Front End Bending in Plate Rolling [PDF]
Transactions of Materials Processing, 2011 The front end bending(FEB) behavior of material that usually occurs in plate rolling is investigated. In this paper, a rollbite profile map approach that systematically predicts the FEB slope is presented. It is based on the concurrent use of shape factors and reduction ratios to ensure an accurate value of the FEB and its slope. In order to obtain the
S.M. Byon, J.H. Lee, S.R. Kim
exaly +2 more sources
Effect of cotton roll biting on pain perception during orthodontic bracket debonding using Weingart pliers: A randomized controlled trial. [PDF]
J Int Med ResObjective This study aimed to evaluate the effectiveness of biting on a cotton roll in reducing pain during metal bracket removal using a Weingart plier compared with the conventional method. Methods This two-arm, parallel-group ...
Drmch BA +4 more
europepmc +3 more sources
Prediction and Analysis of the Force and Shape Parameters in Variable Gauge Rolling
Chinese Journal of Mechanical Engineering, 2022 Variable gauge rolling is a new process to obtain a plate for which the thickness changes continuously by continuously and dynamically adjusting the roll gap upward and downward in the rolling process. This technology is an effective method for producing
Yuanming Liu +6 more
doaj +1 more source
Temporomandibular joint biomechanics and equine incisor occlusal plane maintenance
Frontiers in Bioengineering and Biotechnology, 2023 In equine dentistry, the physiological incisor occlusal surface is visually perceived as a plane with a distinct inclination to the head’s coronal plane, extending rostro-ventrally to caudo-dorsally.
Tomas Rudolf Sterkenburgh +6 more
doaj +1 more source