Results 1 to 10 of about 2,213 (91)

Comparative Validation of the fBrake Method with the Conventional Brake Efficiency Test Under UNE 26110 Using Roller Brake Tester Data [PDF]

open access: yesSensors
In periodic technical inspections (PTIs), evaluating the braking efficiency of light passenger vehicles at their Maximum Authorized Mass (MAM) presents a practical challenge, as bringing laden vehicles to inspection is often unfeasible due to logistical ...
Víctor Romero-Gómez   +1 more
doaj   +5 more sources

Comparative study on the lateral run-out of friction surfaces measurement of brake discs using a brake roller tester and a dial gauge [PDF]

open access: yesMATEC Web of Conferences, 2017
Brake system diagnosis is one of the most common and necessary technical operations applied to the car, regardless of its type and operating phases. Measuring the diagnostic parameters on a roller brake tester is a fast operation with no disassembly ...
Toma Marius   +2 more
doaj   +3 more sources

Comparing Variability of Parameters between Roller Bed Brakes Testers and Dynamometric Platform of Ministry Of Transport Facilities [PDF]

open access: yesMATEC Web of Conferences, 2015
This study gives a comparison between which parameters may vary when braking on two different Ministry of Transport (MOT) brake testers, such as roller bed brake tester and dynamometric platform.
Senabre C, Valero S, Velasco E
doaj   +3 more sources

Measurement Performance Assessment: Dynamic Calibration Compared with Static Calibration Method for Roller Tester of Vehicle Brake Force

open access: yesAdvances in Mechanical Engineering, 2014
The measurement performance of the roller tester for the vehicle brake force is evaluated by both proposed dynamic calibration and traditional static calibration to find an effective way for ensuring the vehicle safety.
Guan Xu   +5 more
doaj   +3 more sources

Development and Characterization of a Compact Device for Measuring the Braking Torque of a Vehicle [PDF]

open access: yesSensors, 2020
In this article, a new force transducer is designed, developed and built for the measurement of braking forces in the wheel rim of a motor vehicle. The parameters of the transducer design are justified using numerical simulation.
Ester Olmeda   +3 more
doaj   +2 more sources

Electronic and GUI Developtmen of Roller Brake Tester

open access: yesJournal of Physics: Conference Series, 2019
Abstract This paper discusses the development of electronic system and Graphical User Interface (GUI) for axle load and brake tester platform own by UPTD PKB DinasPerhubunganKabupaten Banjar Kalimantan Selatan which has not been operated for about 10 years due to failure on its electronic system.
Riky Maulana Firdaus   +2 more
openaire   +2 more sources

Analysis of braking force efficiency measurements for various braking strategy applied for vehicle tested on roller brake tester

open access: yesJournal of Physics: Conference Series, 2020
Abstract Roller brake tester is a kind of vehicle braking system test equipment to test the braking force for each vehicle axis and its efficiency. This study aims to analyze the vehicle braking force efficiency due to application of three different braking actions: sudden braking, gradual braking and intermittent press release braking ...
R M Firdaus, B Supriyo, A Suharjono
openaire   +2 more sources

Dynamic and Stationary Testing of Vehicle Braking Systems

open access: yesActa Technologica Agriculturae, 2023
The paper deals with the dynamic and stationary testing of vehicle braking systems for a selected set of eight intercity buses in an unloaded state. In case of the dynamic test carried out on a defined test area, a decelerometer is used to record the ...
Kožuch Peter   +3 more
doaj   +2 more sources

fBrake, a Method to Simulate the Brake Efficiency of Laden Light Passenger Vehicles in PTIs While Measuring the Braking Forces of Their Unladen Configurations [PDF]

open access: yesSensors
This study introduces fBrake, a novel simulation method now designed for use in periodic technical inspections of M1 and N1 vehicle categories, addressing challenges posed by Directive 2014/45/EU.
Víctor Romero-Gómez   +1 more
doaj   +2 more sources

The Theoretical Analysis of Test Result’s Errors for the Roller Type Automobile Brake Tester [PDF]

open access: yesConference on Control Technology and Applications, 2011
The main testing parameter of the roller brake tester is the braking force. Actually, there are some differences in results even if the same vehicle is tested on the same tester. So it will bring trouble to evaluate the braking performance accurately.
Li, Jun, Zha, Xiaojing, Wu, Dongsheng
openaire   +3 more sources

Home - About - Disclaimer - Privacy