Results 161 to 170 of about 9,727 (308)

Recent Advances in Conductive Rubber Composites: Progress, Challenges, and Emerging Opportunities

Macromolecular Rapid Communications, EarlyView.
This study reviews the recent advances in conductive rubber composites, focusing on key aspects such as material selection, conductive mechanisms, interfacial engineering, processing methods, vulcanization strategies, and practical applications. It also discusses current challenges and highlights emerging directions that are shaping the development of ...
Lu Yin, Ali Vahidifar, Steven Yu, Boxin Zhao   +3 more
wiley   +1 more source

Research on geometric parameter quantification of rail rolling contact fatigue crack damage based on 2D optical image. [PDF]

Sci Rep
Wang Y, Miao B, Zhang Y, Huang Z.
europepmc   +1 more source

Selective Motor Stimulation of the Pudendal Nerve Using Multi‐Contact Cuff Electrodes: A Pre‐Clinical Study in Feline and Ovine Models

Neurourology and Urodynamics, EarlyView.
ABSTRACT Introduction Pudendal nerve stimulation is a promising therapy for urinary incontinence, however stimulation can evoke off‐target activity. We aimed to determine whether multi‐contact cuff electrodes can selectively recruit motor fibers of the pudendal nerve trunk in preclinical feline and ovine models.
Miguel Ortiz‐Lopez, Amador C. Lagunas, Hera Akmal, Tim M. Bruns   +3 more
wiley   +1 more source

Rolling Contact Fatigue Behavior of Pitch Bearing Raceway in Offshore Wind Turbines. [PDF]

Materials (Basel)
He H, Chen Y, Liu Y, Zhu Y, Jin X.
europepmc   +1 more source

Life Models in Rolling Contact Fatigue

, 2013
Rolling contact fatigue (RCF) unavoidable mode of failure observed in two surfaces which are rolling with relative to each other. Rolling contact fatigue is the name given to crack growth and material damage generated as a result of high loads ...
Bhalerao, Yogesh Jayant, Mankar, Ankush, Ghalme, Sachin Ganpatrao   +2 more
core  

Embedding Fiber Segment Interferometry for Localization of Defects in Composite Structures

Polymer Composites, EarlyView.
Graphical representation of composite structures with embedded fiber optic sensors for structural health monitoring, enabling strain measurement and damage localization under mechanical loading. ABSTRACT In the area of structural health monitoring (SHM), embedding strain sensors into smart composites is a key strategy for detecting failures arising ...
Shiva Mohammadkarimi, Christoph Hemeling, Thomas Kissinger, Florian Puch   +3 more
wiley   +1 more source

Assessment of polytetrafluoroethylene composites for deep groove ball bearing applications through free run and rolling contact fatigue tests. [PDF]

Sci Rep
Deshwal D, Belgamwar SU, Bekinal SI.
europepmc   +1 more source

Thermoplastic‐Resin Transfer Molding Technology: Development and Challenges Toward Industrialization

Polymer Composites, EarlyView.
Illustration of the key aspects involved in the manufacture of thermoplastic composites by T‐RTM highlighting the relationships between raw materials, resin mixing strategies, polymerization parameters, and processing equipment ranging from laboratory to industrial scale. ABSTRACT Driven by increasingly stringent international environmental regulations,
Filipe P. Martins, Paulo S. Lima, Ricardo Torcato, Laura Santos, J. M. Oliveira   +4 more
wiley   +1 more source

A Review of Mechanical Reinforcement and Piezoresistive Self‐Sensing in Carbon Nanotube Fiber Composites

Polymer Composites, EarlyView.
PSPP‐TRL mapping of CNT‐modified CFRP literature, with four recurring confusions resolved and five scale‐up problems quantified. ABSTRACT Carbon nanotube‐modified fiber composites are often presented as a route to stronger, tougher, and self‐sensing structural materials.
Sanan H. Khan
wiley   +1 more source

Influence of Thermal Cycling on Friction, Wear, and Damage Evolution of Fused Deposition Modeling of 3D‐Printed Glass Fiber Reinforced Polylactic Acid Composites

Polymer Composites, EarlyView.
Schematic illustration of the experimental procedure of the specimens. ABSTRACT This research work investigated the effect of the cyclic thermo‐hygrometric aging regime between −20°C and +40°C with 0–400 cycles on the reciprocating tribological properties of fused deposition modeling (FDM) printed polylactic acid (PLA) and the same material reinforced ...
Sinan Fidan, Satılmış Ürgün, Nevin Gamze Karsli, Taner Yılmaz, Mustafa Özgür Bora, Mehmet İskender Özsoy   +5 more
wiley   +1 more source