Results 51 to 60 of about 1,912,866 (270)
Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring
Advanced Engineering Materials, EarlyView.Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Binder‐free laser powder bed fusion of 8YSZ with a femtosecond laser is used to map process windows linking scan strategy, heat accumulation, and grain growth. Time‐resolved thermography and simulations reveal thermal regimes that enable continuous, vitrified, and fine‐grained 8YSZ surface layers without absorptive additives and demonstrate ...
Markus Kühn +5 more
wiley +1 more source
A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation
Advanced Engineering Materials, EarlyView.A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler +4 more
wiley +1 more source
Investigation into the Rolling Process of 20CrNiMo/Incoloy 825 Composite Materials
CrystalsThis paper is focused on the rolling finite element simulation and experimental study of 20CrNiMo/Incoloy 825 composite materials. Firstly, single-pass rolling finite element simulations of the composite materials were conducted.
Jie Liu +4 more
doaj +1 more source
Finite element modeling and analysis for the integration–rolling–extrusion process of spline shaft
Advances in Mechanical Engineering, 2017 An integration–rolling–extrusion process is raised for the manufacture of spline shaft in this study. First, the principle and procedures of integration–rolling–extrusion process are described.
Minchao Cui +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This perspective reframes additive manufacturing for electrical machines as a qualification‐limited materials and architecture design problem. It links process–structure–property–performance relationships to magnetic, conducting, dielectric, and thermal property windows, highlighting where AM can enable segmented magnetic circuits, permanent magnet ...
Dénes Fodor, Loránd Szabó
wiley +1 more source
Application of morphological component analysis for rolling element bearing fault diagnosis
工程科学学报, 2017 Periodical impulses in vibration signals are key features in rolling element bearing fault diagnosis. Based on an overcomplete dictionary composed of different morphological atoms, morphological component analysis can be used to extract the signal ...
LIU Yong-bing +2 more
doaj +1 more source
Supporting AI Readiness Through Digital Workflows in Materials Science
Advanced Engineering Materials, EarlyView.Digitalization drives innovation in materials science by connecting data silos and turning heterogeneous processes into reusable research pipelines. Across 13 MaterialDigital projects, digital workflows reveal complementary pathways toward AI‐ready materials research, founded on structured data, persistent artifacts, executable orchestration, and ...
Marian Bruns +67 more
wiley +1 more source
The influence of heterogenous porosity on silicon nitride/steel wear in lubricated rolling contact [PDF]
, 2000 Heterogeneous porosity is detected on the surface and subsurface of hot isostatically pressed (HIPed) silicon nitride spherical rolling elements. The extent of the localised porosity accounts for an area of 6% of the rolling element surface and 4% of the
Kang, J, Hadfield, M
core +4 more sources
Advanced Engineering Materials, EarlyView.PUF/ENB microcapsules were synthesized based on a sequential factorial design and incorporated into an epoxy matrix. Their anticorrosive action, associated with the self‐healing mechanism, demonstrated that the addition of microcapsules to the coating improved anticorrosive performance compared to pure epoxy coatings, particularly when the encapsulate ...
Vandicleya Alves Moreira +6 more
wiley +1 more source