Results 161 to 170 of about 4,431 (262)

Research on Intelligent Control Method of Camber for Medium and Heavy Plate Based on Machine Vision. [PDF]

Materials (Basel)
He C, Yue C, Zhao Z, Wu Z, Jiao Z.
europepmc   +1 more source

Mode I and Mode II Interlaminar Fracture Toughness of Basalt/Kevlar Fiber Reinforced Epoxy Resin Hybrid Composites Incorporating Graphene Nanoplatelets

Polymer Composites, EarlyView.
Processing the Mode I and Mode II fracture analysis Basalt/Kevlar fiber reinforced hybrid composites with GnP. ABSTRACT This research examines the Mode I and Mode II fracture behavior of basalt/Kevlar fiber reinforced epoxy hybrid composites augmented with graphene nanoplatelets (GnP). Hybrid composites containing varying concentrations of GnP (0, 1, 2
Mehmet Bulut, Ömer Yavuz Bozkurt, Atban R. Abdo, Ahmet Erkliğ   +3 more
wiley   +1 more source

Synergistic optimization of shape-force and dynamic coupling effect in bending roll systems during accelerated rolling. [PDF]

Sci Rep
Yan ZW, Tang YX, Pan SZ, Cao WJ, Wu JW.
europepmc   +1 more source

Nonwoven rCF/PA6 Thermoplastic Composites: Hybrid Commingled Fibers vs. Powder Impregnation—Effects on Microstructure and Mechanical Properties

Polymer Composites, EarlyView.
Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia, Tommaso Pini, Ilaria Rossitti, Sara Taherinezhad Tayebi, Marco Valente   +4 more
wiley   +1 more source

Influence of Thermal Cycling on Friction, Wear, and Damage Evolution of Fused Deposition Modeling of 3D‐Printed Glass Fiber Reinforced Polylactic Acid Composites

Polymer Composites, EarlyView.
Schematic illustration of the experimental procedure of the specimens. ABSTRACT This research work investigated the effect of the cyclic thermo‐hygrometric aging regime between −20°C and +40°C with 0–400 cycles on the reciprocating tribological properties of fused deposition modeling (FDM) printed polylactic acid (PLA) and the same material reinforced ...
Sinan Fidan, Satılmış Ürgün, Nevin Gamze Karsli, Taner Yılmaz, Mustafa Özgür Bora, Mehmet İskender Özsoy   +5 more
wiley   +1 more source

Tailor-Made Vessels for Enhancing the Mechanochemical Energy Transfer and Milling Efficiency. [PDF]

ChemSusChem
Jansen T, Thomas LC, Bolm C.
europepmc   +1 more source

Processability Assessment of Recycled Polymeric Nonwoven Materials in Injection Molding, Film Extrusion and Additive Manufacturing

Polymer Engineering &Science, EarlyView.
Recycled nonwoven face masks are transformed into polymer feedstocks for injection molding, film extrusion, and additive manufacturing. Rheological behavior links composition to processability, enabling material selection and blending strategies.
Daniele Battegazzore, Fulvia Cravero, Giulia Bernagozzi, Rossella Arrigo, Alberto Frache   +4 more
wiley   +1 more source

A scaling up of flattening silver particles using dry ball milling by DEM simulation. [PDF]

Sci Rep
Kojima T, Kushimoto K, Oka D, Hisaeda Y, Kano J.   +4 more
europepmc   +1 more source

Reinforcement and Rheology of Epoxy‐Mediated Lignin Integration in Carboxylated Nitrile Rubber

Polymer Engineering &Science, EarlyView.
The interaction of lignin‐epoxy resin‐XNBR and the effect of lignin on the nonlinear rheological behavior of epoxy‐cured XNBR/lignin composites. ABSTRACT Lignin has attracted increasing interest as a renewable filler for rubber composites; however, it shows weaker reinforcing efficiency than conventional fillers such as carbon black and silica ...
Onur Nuri Arslan, Chaoying Wan
wiley   +1 more source

Analysis of Roll Pass Wear in the Railway Rail Rolling Process. [PDF]

Materials (Basel)
Szota P, Mróz S, Stefanik A, Zygmunt T, Bołda M.   +4 more
europepmc   +1 more source