Results 161 to 170 of about 30,905 (302)

Stuck in transition - admission to the neonatal intensive care unit after shoulder dystocia: analysis of risk factors and assessment of postnatal care. [PDF]

Matern Health Neonatol Perinatol
Rahn A, Böhne C, Bohnhorst B, Pirr S, Peter C, Kleiner S, Mindermann C, Galland P, Dütemeyer V, von Kaisenberg C, Brodowski L.   +10 more
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Perceptions of Nurses, Patients, and Family Members on Rooming-In in Adult Care: A Cross Sectional Survey Study. [PDF]

J Adv Nurs
de Vries CEJ, van der Heijden MJE, Eskes AM, Ista E, van Dijk M.   +4 more
europepmc   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Longitudinal Association of Maternity Care Practices with Exclusive Breastfeeding in U.S. Hospitals, 2018-2022. [PDF]

Children (Basel)
Gosdin L, Marks KJ, Addo OY, O'Connor L, Awan S, Grossniklaus DA, Hamner HC.   +6 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Evolução da assistência materno-infantil na cidade de São Paulo (1984-1996)

Revista de Saúde Pública
OBJETIVO: Descrever a evolução da assistência materno-infantil, com base nas informações extraídas de dois inquéritos domiciliares realizados nos anos de 1984/85 e de 1995/96, na cidade de São Paulo, SP.
Carlos Augusto Monteiro, Ivan França Júnior, Wolney Lisboa Conde   +2 more
doaj  

A QI Approach to Lower Hypertension and Elevate Care in an Internal Medicine Residency Community Clinic. [PDF]

JACC Case Rep
Spaeth LD, Beason ER, Ramos K, Scherer KM, Scerbo DA, Barlow MP.   +5 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Consumed by Abdominal Distention

Arthritis Care &Research, EarlyView.
Abimbola Fadairo‐Azinge, James Grenert, Brian Haas, Mary Margaretten   +3 more
wiley   +1 more source