Results 31 to 40 of about 17,403 (263)

Inertial torques acting on a spinning paraboloid

AIP Advances, 2020
Numerous gyroscopic devices consist of rotating components that manifest gyroscopic effects, i.e., the action of unexplainable inertial torques. The rotating objects in engineering can be designed as a disk, cylinder, rotor, circular cone, sphere ...
R. Usubamatov, A. Arzybaev
doaj   +1 more source

A new flow chip in combination with multiphoton microscopy as a protocol for longitudinal 3D imaging of tissue calcification under shear stress

FEBS Open Bio, EarlyView.
Miniaturized flow chip platform enabling continuous perfusion and longitudinal multiphoton 3D imaging of vascular smooth muscle cell constructs under physiological flow. Brightfield imaging guides region selection, while CellTracker Green and mRuby‐labeled fetuin‐A visualize cells and mineral deposition, respectively. Magnesium supplementation markedly
Vytautas Kučikas, Aaron D. Morgan, Ignas Čiurlionis, Christian Böhm, Stefan Jockenhövel, Willi Jahnen‐Dechent, Marc A. M. J. van Zandvoort   +6 more
wiley   +1 more source

Topology optimization of disk–shaft rotating body under thermomechanical coupling

Case Studies in Thermal Engineering
Turbine rotors often operate under harsh conditions, such as high rotational speeds and large temperature gradients, that requires them to withstand complex thermal and centrifugal loads.
Yu Wang, Renfu Li, Xiaowei Liu, Kun Wang
doaj   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Clearance flow patterns and pressure distribution of a pump-turbine: Measurement and simulation of a rotating disk flow

Frontiers in Energy Research, 2022
The clearance flow patterns and pressure distribution determine the clearance axial hydraulic thrust of a pump turbine, which has a substantial impact on the unit axial imbalance.
Xiaoxia Hou, Herui Liu, Yongguang Cheng, Ke Liu, Demin Liu, Hongyu Chen   +5 more
doaj   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

String-Wrapped Rotating Disks [PDF]

, 2012
Let the centers of a finite number of disjoint, closed disks be pinned to the plane, but with each free to rotate about its center. Given an arrangement of such disks with each labeled + or −, we investigate the question of whether they can be all wrapped by a single loop of string so that, when the string is taut and circulates, it rotates by friction
openaire   +2 more sources

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source