Results 121 to 130 of about 85,518 (307)
Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)
Advanced Engineering Materials, EarlyView.Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho +8 more
wiley +1 more source
Power variation with respect to the rotational speed of the low-speed shaft.
Power variation with respect to the rotational speed of the low-speed shaft.
Liu Jun Jun (17811108) +6 more
core +1 more source
The Effect of Drill Rotational Speed on Drilling Resistance in Non-Destructive Testing of Concrete
Applied SciencesDrilling resistance (DR) measurement is a promising non-destructive technique for evaluating the mechanical properties of concrete. However, the reliability and repeatability of DR measurements are still limited by an insufficient understanding of how ...
Rauls Klaucans +5 more
doaj +1 more source
MATEC Web of Conferences, 2017 The maximum horizontal impact load experienced by the aircraft landing gear wheel during landing is an important parameter in landing gear safety design and performance analysis. Using a non-contact photoelectric testing method, this paper experimentally
Wang Huaitao, Wu Dafang, Wang Feng
doaj +1 more source
Apparent length of a rotating arc-line as a function of speed of rotation
Acta Psychologica, 1968 Abstract Magnitude estimates were obtained of 3, 6, 9 and 12 cm illuminated arcs rotating at 30, 45, 60 and 75 r.p.m. in a path of rotation twelve degrees from the point of fixation. The Ansbacher Shrinkage Effect was obtained, there being a tendency for greater shrinkage with increase in speed.
openaire +2 more sources
An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials
Advanced Engineering Materials, EarlyView.An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut +16 more
wiley +1 more source
Position control under simultaneous limited torque and speed of a torque-driven nonlinear rotational mechanism [PDF]
, 2016 "This paper deals with shaft displacement regulation (position control) of a torque-driven nonlinear gravity unbalanced mechanism under both prescribed bounded torque and speed. This is a novel control objective formulation for mechanisms.
ADRIANA SALINAS AVILA
core +1 more source
On Critical Speeds Induced by Ball Bearings in Lower Rotating Speeds
Transactions of the Japan Society of Mechanical Engineers, 1957 When single-row radial ball bearings are used, several critical speeds take place in a vertical shaft at certain rotating speeds lower than the major critical speed. When the bearing center line of both bearing pedestals is not in alignment and the shaft is not in a perfectly straight line, there is the possibility that these critical speeds occur. The
openaire +3 more sources
Advanced Engineering Materials, EarlyView.Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley +1 more source
Rotary Friction Welding of Polyetheretherketone Biopolymer Rods Using Variable Rotational Speed. [PDF]
Polymers (Basel), 2023 Kuo CC, Liang HX, Huang SH, Tseng SF.
europepmc +1 more source